Introduction: Why THFA Is a Different Kind of Reactive Diluent
Tetrahydrofurfuryl acrylate (THFA) is the acrylate ester of tetrahydrofurfuryl alcohol: an unsubstituted acrylate double bond on one side of the ester, and a saturated tetrahydrofuran ring on the other. The combination looks simple, but it is precisely the mismatch between the two ends that makes the monomer useful. The acrylate end cures quickly and crosslinks readily with standard photoinitiators and acrylated oligomers; the saturated, strongly polar cyclic ether end does not take part in the cure at all and instead stays pendant on the polymer chain, where it wets difficult surfaces, hydrogen-bonds to polar substrates and plasticises the network from the inside.
Formulators therefore treat THFA less as a viscosity reducer and more as an adhesion and wetting monomer. It is used where ordinary acrylate monomers fail to grip: polycarbonate, polyester, printed or coated surfaces, glass, metal, and the potting of hollow-fibre membrane modules where curing stress would otherwise damage the element.
Chemical Identity and Commercial Forms
THFA is a monofunctional acrylate ester, supplied as a stabilised liquid in technical, coating, electronic and high-purity grades. Buyers should confirm the CAS number on the Certificate of Analysis, because several tetrahydrofuran-containing monomers circulate under similar trade names and a substitution changes both cure speed and substrate compatibility.
| Item | Description |
|---|---|
| Chemical name | Tetrahydrofurfuryl acrylate |
| Systematic name | (Tetrahydrofuran-2-yl)methyl prop-2-enoate |
| Synonym / abbreviation | Tetrahydro-2-furanylmethyl acrylate; acrylic acid tetrahydrofurfuryl ester; THFA |
| CAS Registry Number | 2399-48-6 |
| Molecular formula | C8H12O3 |
| Molecular weight | 156.18 g/mol |
| Functional class | Monofunctional acrylate with a saturated cyclic ether (tetrahydrofuran) ring |
| Polarity | Medium to high, arising from the ether oxygen; substantially more polar than alkyl acrylates such as butyl acrylate or 2-ethylhexyl acrylate |
| Grades offered | Technical, UV-coating, electronic and low-colour polymerisation grades; inhibitor level adjusted for transit and shelf life |
Physical and Chemical Properties That Drive Formulation Choices
The following values represent the ranges normally published for commercial THFA. They are identity and consistency indicators; batch acceptance must be based on the Certificate of Analysis, not on published typicals.
| Property | Typical value / behaviour |
|---|---|
| Appearance at 25 C | Transparent, colourless liquid |
| Specific gravity | 1.06 to 1.07 at 25 C, i.e. denser than water |
| Refractive index | Approximately 1.436 (nD, 25 C) |
| Surface tension | Approximately 31.2 dyne/cm, which supports substrate wetting and levelling of thin films |
| Water solubility | Limited but higher than that of purely aliphatic acrylates; the ester hydrolyses slowly under acidic or basic conditions |
| Solvent compatibility | Readily miscible with esters, ketones, alcohols, glycol ethers, aromatic hydrocarbons and the usual acrylated oligomers |
| Volatility | Low; a high boiler that is distilled under reduced pressure, so monomer loss and odour in the curing line are limited |
| Flammability | Flash point well above the 60 C threshold that defines a flammable liquid; ordinary commercial grades are not treated as flammable liquids for transport |
| Polymerisation inhibitor | Monomethyl ether of hydroquinone (MEHQ) or hydroquinone, typically in the range of a few hundred parts per million, agreed contractually with the customer |
| Reactivity | Free-radical homo- and copolymerisation under UV, electron beam, thermal or redox initiation; uninhibited product can gel on warming |
The Chemistry Behind the Adhesion: Polarity Without Conjugation
Two structural features explain most of the technical behaviour of THFA.
A saturated ether ring with strong polarity. The tetrahydrofuran oxygen is a good hydrogen-bond acceptor. Unlike a vinyl or aryl ether, the oxygen lone pairs are not delocalised into a conjugated system, so the ring behaves like a polar, chemically inert solvent that remains permanently attached to the polymer network. That polarity lowers the interfacial tension between the uncured formulation and polar substrates, giving better wetting and a more intimate contact with polycarbonate, polyester, poly(methyl methacrylate), polyamide, ABS, glass and metal oxide surfaces than an aliphatic acrylate can achieve.
No absorption in the near-UV and no yellowing pathway. Because the ring is saturated, it does not absorb in the region where photoinitiators are activated and it cannot form the conjugated, coloured by-products that arise from unsaturated ether groups. Cured films therefore keep their clarity and retain their colour after weathering, which matters for optical, display and decorative applications.
Internal plasticisation and swelling behaviour. The pendant ring reduces network density and internal stress, so the cured film is flexible and adheres well on rigid or dimensional substrates. The same polarity and mobility produce a measurable swelling effect on some thermoplastics, especially polycarbonate and polyethylene terephthalate. This is a benefit when bonding such substrates, because swelling-assisted interpenetration improves adhesion, but a risk when the substrate is a thin film, an optical part or a stressed moulding: swelling can cause stress-cracking, haze or warping. Formulators therefore evaluate THFA on the actual substrate rather than assuming that high polarity always means better bonding.
Formulation Role: Reactive Diluent, Adhesion Monomer and Crosslinking Partner
THFA is almost never used alone. Its typical roles are:
Reactive diluent: reduces the viscosity of acrylated epoxy, urethane and polyester oligomers while remaining in the film as a co-monomer, giving a permanent plasticising and wetting effect rather than the solvent loss associated with inert diluents.
Adhesion promoter: added at modest levels to UV adhesives, laminating adhesives and coatings applied to plastics, glass, metals and coated or printed surfaces.
Crosslinking and property modifier: when combined with multifunctional acrylates it raises the polarity of the network and improves adhesion, pigmentation compatibility and hydrolytic stability without pushing the modulus as high as a purely multifunctional diluent would.
Compatibility aid: improves pigment and filler wetting in heavily loaded UV inks and coatings, which limits flocculation, gloss loss and settling.
Cure-profile modifier: in amino-resin or hybrid thermally cured systems, blends containing THFA allow curing at lower temperatures for the same degree of conversion and act as a plasticising co-monomer.
A working rule is that THFA lowers viscosity and increases adhesion, while it also lowers the glass transition temperature of the network. Systems that must keep a high modulus or strong solvent resistance normally pair THFA with a harder, more functional monomer rather than raising the THFA loading indefinitely.
Application Areas and Substrate Fit
| Application | Function of THFA | Substrate / end use |
|---|---|---|
| UV inks for screen and inkjet printing | Low-viscosity monomer that wets and grips difficult surfaces; combined with urethane acrylate resins for print quality on plastics and coated board | Polycarbonate and polyester signs, labels, industrial graphics, membrane switches |
| UV-curable coatings | Reactive diluent that improves adhesion, flexibility and pigment wetting in thin films | Graphite heat-dissipation films, plastic and metal decoration, electronics housings |
| Adhesives | Adhesion and flexibility monomer in structural, UV and laminating adhesives; blends give bond strength over a wide temperature range | Plastic-to-plastic and plastic-to-metal bonding, optical bonding, assembly adhesives |
| Membrane module potting | Low-stress, flexible potting and casting formulations that do not damage delicate hollow-fibre elements | Water-treatment and separation membrane modules |
| Wafer processing adhesives | Component of single-component temporary bonding adhesives used in wafer thinning and handling, formulated for clean release | Semiconductor wafer fabrication support material |
| Polymer and intermediate synthesis | Monomer for specialty acrylic polymers, dispersants and stabilisers; intermediate for further functionalisation of the ring | Coatings additives, resin modification, laboratory and industrial synthesis |
| Photopolymer and additive-manufacturing resins | Wetting and toughness monomer in vat-photopolymerisation formulations, reducing warpage and improving layer adhesion | Functional prototypes, jigs and fixtures, tough photopolymer parts |
Quality Control and Typical Specification Limits
THFA is tested with the same toolkit as other acrylate monomers, with particular attention to residual alcohol, acid value and inhibitor level because these three parameters move first when a batch is exposed to heat or moisture.
Purity: typically 98 percent minimum by gas chromatography, calibrated against an external standard; the chromatogram should separate THFA from tetrahydrofurfuryl alcohol, from the corresponding dimeric by-products and from any higher-boiling residue.
Water: 0.20 percent maximum by Karl Fischer titration following the principles of GB/T 6283.
Acid value: usually 0.5 mg KOH per gram maximum, titrated with standardised alkali prepared in line with GB/T 601; a rising value signals hydrolysis to acrylic acid and alcohol.
Colour: 50 Hazen maximum for standard grades, 20 or lower for optical and electronic grades, which also typically cap trace metals such as iron and copper.
Inhibitor: MEHQ or hydroquinone by HPLC within a contracted window, commonly a few hundred parts per million; the window protects the batch during transport without retarding cure in the customer's line.
Identity: density, refractive index and surface-tension behaviour compared with the certified values, with infrared spectroscopy available for confirmation.
Sampling and packaging marks: sampling in line with GB/T 6678 principles, packaging symbols per GB/T 191.
Customers running UV inks and optical coatings frequently add their own incoming checks: a small-scale cure test at fixed dose, a colour measurement of the cured film, and an adhesion test on the actual substrate using the method they will apply in production.
Storage, Handling and Shelf Life
Store between about 5 C and 25 C in sealed, shaded, dry and well-ventilated surroundings; heat and sunlight deplete the inhibitor and can initiate gelling, particularly at the drum wall.
Keep away from peroxides, azo compounds, oxidising agents, mineral acids, strong bases and any source of ignition; use only dedicated, clean pumps and lines.
Avoid iron, copper, zinc and their alloys in contact with the liquid; corrosion products cause discolouration and can catalyse decomposition. Stainless steel, glass and polyethylene or lined vessels are appropriate.
Preserve the specified oxygen content in the headspace so that the inhibitor remains effective, and keep containers closed to limit moisture uptake, which raises the acid value over time.
Typical packaging is 25 kg and 200 kg polyethylene or lined steel drums and 1000 kg intermediate bulk containers, with dedicated stainless steel tanks for bulk deliveries.
Under good conditions shelf life is six to twelve months. Re-test assay, water, acid value and inhibitor before use after long storage, and never use material that shows thickening, cloudiness or gel particles.
Personal protection follows the Safety Data Sheet: local exhaust ventilation, splash goggles, nitrile or laminated gloves and protective clothing. THFA is an acrylate ester and is handled as a skin and eye irritant with sensitising potential, so repeated skin contact must be avoided.
Regulatory, Environmental and Transport Notes
Acrylate monomers of this type are normally classified under the GHS and the EU CLP Regulation for skin irritation, serious eye irritation, skin sensitisation and, in many supplier classifications, respiratory irritation, with hazard and precautionary statements taken from the batch Safety Data Sheet prepared in line with ISO 11014. Because the flash point is well above 60 C, ordinary commercial grades are not classified as flammable liquids under ADR, RID or IMDG and are not assigned a UN number on that basis. Acrylate esters are also frequently subject to an aquatic hazard classification; spills must be absorbed with inert material and must never be washed into drains, soil or surface water.
On chemical control, THFA is a registered or listed substance under the principal industrial chemical frameworks, including REACH in the European Union and TSCA in the United States, with corresponding national inventories in Asia. Importers should verify inventory status and any national notification requirement before shipment. Documentation expectations for a professional purchase are a batch Certificate of Analysis, a current Safety Data Sheet and, for food-contact or medical-adjacent applications, confirmation that the grade and the residual monomer limits are acceptable for the intended use.
Selection and Acceptance Guidance for Buyers
Specify the CAS number 2399-48-6, the grade and the inhibitor window; do not rely on the abbreviation THFA alone, as it is also used loosely for the methacrylate analogue in some markets.
Decide between THFA and tetrahydrofurfuryl methacrylate on technical grounds: the acrylate cures faster and is softer and more flexible, whereas the methacrylate offers lower shrinkage, slower cure and better thermal stability. The two are not interchangeable in a validated formulation.
Test adhesion and swelling on the real substrate. The same polarity that improves bonding to polycarbonate and polyester can cause stress-cracking in thin or highly stressed parts.
Check the arrival condition: temperature history, drum integrity and colour. Colour shift without an assay change usually points to heat exposure during transit.
Confirm that the acidity and water limits are tight enough for the application; conductive, optical and semiconductor-adjacent uses tolerate far less ionic contamination than general industrial coatings.
FAQ
Q: What is THFA and what is its CAS number?
THFA is tetrahydrofurfuryl acrylate, CAS 2399-48-6, molecular formula C8H12O3, molecular weight 156.18 g/mol. It is a monofunctional acrylate ester carrying a saturated tetrahydrofuran ring, supplied as a stabilised transparent liquid for UV and thermally cured systems.
Q: Why does THFA adhere so well to plastics and metals?
The tetrahydrofuran oxygen is a strong hydrogen-bond acceptor that is not conjugated into any unsaturated system, so the ring remains a permanently polar, mobile pendant group. It lowers the interfacial tension of the formulation, wets polar surfaces more completely and, on thermoplastics such as polycarbonate, promotes interpenetration through a controlled swelling effect.
Q: Can THFA be used at very high loading to thin a formulation?
It can, but monofunctional acrylates reduce crosslink density and lower the glass transition temperature of the cured film. Where hardness, blocking resistance or chemical resistance must be maintained, part of the dilution should come from multifunctional acrylates and the THFA level should be kept to the amount needed for wetting and adhesion.
Q: What are the typical specification limits for incoming THFA?
A common technical specification is 98 percent minimum assay by gas chromatography, 0.20 percent maximum water by Karl Fischer titration, 0.5 mg KOH per gram maximum acid value, 50 Hazen maximum colour, and an inhibitor content agreed within a contracted window and verified by HPLC.
Q: Is THFA a dangerous good for shipment?
Its flash point is well above 60 C, so ordinary commercial grades are not classified as flammable liquids for road, sea or air transport and carry no UN number on that basis. The transport classification, aquatic hazard statement and any national requirement are stated in the batch Safety Data Sheet, which is prepared in accordance with ISO 11014.
Q: How should THFA be stored and how long does it keep?
Keep it sealed at 5 to 25 C, shaded and dry, away from initiators, oxidisers, acids and metal contamination, with the headspace oxygen preserved so the inhibitor can work. Six to twelve months is a realistic shelf life; after that, re-test assay, water, acid value and inhibitor content before releasing the material to production.





