What 4-Chlorobutyryl Chloride Is: Identity and Structural Logic
4-Chlorobutyryl chloride is an aliphatic acyl chloride in which a four-carbon chain carries both a reactive acid-chloride group and a terminal chlorine atom. Its molecular formula is C4H6Cl2O, its molecular weight is 140.99 g/mol, its CAS registry number is 4635-59-0 and its EINECS/EC number is 225-059-1. The structure can be written as ClCH2CH2CH2COCl, and it is also known as 4-chlorobutanoyl chloride, 4-chlorobutyric acid chloride or gamma-chlorobutyryl chloride.
The molecule is best understood as a bifunctional building block. The acid chloride end is a strong electrophile that acylates alcohols, amines and aromatic rings, while the terminal carbon-chlorine bond at the other end behaves as an alkyl halide and can be displaced by nucleophiles or used in intramolecular cyclisation. Because those two reactive sites are separated by a three-carbon spacer, the compound is a convenient way to install a four-carbon chain that carries a latent leaving group - a pattern that appears in several pharmaceutical and agrochemical structures. That same bifunctionality explains why it is a demanding material to store and handle: both ends of the molecule react readily, and moisture attacks the acid chloride first.
Physical and Chemical Properties
The table below collects the reference data normally published for 4-chlorobutyryl chloride. Where a property is strongly dependent on purity, the note column explains the practical consequence for specification work.
| Property | Reference value | Practical note |
|---|---|---|
| Name | 4-Chlorobutyryl chloride | Also called 4-chlorobutanoyl chloride |
| CAS registry number | 4635-59-0 | EC/EINECS 225-059-1 |
| Molecular formula | C4H6Cl2O | Bifunctional: acid chloride plus alkyl chloride |
| Molecular weight | 140.99 g/mol | Used for charge calculations and stoichiometry |
| Appearance | Colourless to pale yellow liquid | Colour deepening is often the first visible sign of decomposition |
| Odour | Pungent, lachrymatory | Very low odour threshold; local exhaust ventilation is essential |
| Boiling point | Approximately 173-174 °C at atmospheric pressure | Purification is normally done under reduced pressure to limit thermal load |
| Density | About 1.26 g/cm3 (25 °C) | Denser than water; sinks and reacts if water is present |
| Refractive index | nD20 about 1.46 | A convenient, fast in-process identity check |
| Vapour density | About 4.9 (air = 1) | Vapour is heavier than air and gathers in low areas |
| Behaviour with water | Hydrolyses, releasing hydrogen chloride | Drives all storage, packaging and ventilation requirements |
| Thermal stability | Decomposes on prolonged heating | Distil gently under vacuum; avoid extended high-temperature hold times |
Two of these values deserve emphasis for buyers. First, the lachrymatory character of the material is intense and is a quality-of-life and occupational-hygiene issue as much as a safety issue: a leaking flange or a poorly sealed drum will produce eye irritation in the working area long before any analytical result changes. Second, the vapour is heavier than air, so natural ventilation at bench height is not sufficient - air must be drawn from low level.
Reactivity of an Acyl Chloride: Why Moisture Control Dominates Handling
4-Chlorobutyryl chloride behaves like a typical aliphatic acyl chloride, and its reaction chemistry follows from the electrophilic carbonyl carbon generated by the adjacent chlorine atom.
Hydrolysis. With water the compound hydrolyses to 4-chlorobutyric acid and hydrogen chloride. The reaction is fast and exothermic and it proceeds with any available moisture, including atmospheric humidity and damp equipment. This single reaction is responsible for the practical rule that the material must be kept sealed, dry and away from all aqueous streams, and it explains why the compound decomposes and can build pressure in a badly sealed container.
Acylation of nucleophiles. Alcohols give 4-chlorobutyrate esters and amines give 4-chlorobutyramides, in each case with liberation of hydrogen chloride. Acid scavengers are normally required in downstream processes, and the choice of scavenger influences the yield and the purity of the amide or ester. From a supply perspective, this is why the material is sold as an acylation reagent rather than as an end product.
Friedel-Crafts acylation. Aromatic substrates are acylated to give 4-chlorobutyrophenone-type ketones, and because the terminal chlorine remains available, those ketones can be converted further. A well-documented example in the pharmaceutical literature is the conversion of 4-chlorobutyrophenone derivatives into cyclopropyl ketones under basic conditions, and the use of 4-chloro-4'-fluorobutyrophenone as a precursor of the butyrophenone antipsychotic haloperidol.
Substitution at the terminal carbon. The primary alkyl chloride is displaced by nucleophiles such as amines, alkoxides, thiolates and carboxylates, which is what makes the four-carbon spacer useful: an amide or ketone prepared from this acid chloride carries a handle for a second, chemically different coupling step.
Cyclisation. Intramolecular reactions of the products lead to four- and five-membered rings and to lactam- and lactone-type heterocycles, making the compound a starting point for ring systems rather than only for linear chains.
Incompatibilities. Water, alcohols, amines, alkalis, strong oxidising agents, and moist metals are all incompatible in the sense that they consume the material or accelerate decomposition. Storage areas should keep these materials physically separated.
Manufacturing Route and Position in the Value Chain
4-Chlorobutyryl chloride is produced on an industrial scale from 4-chlorobutyric acid, which is itself obtained by chlorination of butyrolactone or by related routes from butanediol chemistry, and the acid is then converted to the acid chloride with a chlorinating agent. The reaction sequence is a standard carboxylic acid to acyl chloride transformation followed by careful purification by vacuum distillation.
The compound sits in the middle of a fine-chemical value chain. Its raw-material side is connected to butanediol and gamma-butyrolactone producers; its downstream side connects to pharmaceutical and agrochemical manufacturers who use it as an acylating agent and as a carbon-chain building block.
Commercial Grades, Specifications and Packaging
| Parameter | Typical commercial specification | Why it matters |
|---|---|---|
| Assay (GC) | 98.0% minimum; 99.0% minimum for pharmaceutical use | Unreacted acid or starting material shifts stoichiometry in downstream reactions |
| Appearance | Clear, colourless to pale yellow liquid | Colour indicates thermal or hydrolytic degradation |
| Hydrolysable chloride / acidity | Reported as hydrochloric acid equivalent or as total acyl chloride | Confirms that the acid chloride function is intact |
| Water content | Low, typically not more than a few hundred ppm | Water hydrolyses the product and corrodes packaging |
| Heavy metals and iron | Low ppm limits | Iron can catalyse degradation and is critical for catalytic downstream steps |
| Packaging | Sealed polyethylene-lined steel drums or intermediate bulk containers, typically 200-250 kg net | Moisture and vapour must both be excluded |
| Storage | Cool, dry, dark, well-ventilated area under an inert gas blanket where practicable | Heat and light accelerate decomposition |
Because the material is corrosive and lachrymatory, packaging is not a cosmetic issue: gaskets, linings and closures must be resistant to hydrogen chloride, and the container must be gas-tight. Suppliers commonly offer two quality tiers - a technical grade for general acylation work and a high-purity grade with tighter colour, water and trace-metal limits for pharmaceutical intermediates. Buyers specifying a pharmaceutical grade should state the assay method, the water limit and the trace-metal limits explicitly, because "high purity" means different things to different producers.
Primary Applications and Downstream Chemistry
Pharmaceutical intermediates. The best-known application is in the butyrophenone class of antipsychotic drugs. Acylation of a fluorobenzene ring with 4-chlorobutyryl chloride gives 4-chloro-4'-fluorobutyrophenone, which is then elaborated into haloperidol, a dopamine-receptor-antagonist antipsychotic. Related butyrophenone-type active ingredients and their intermediates rely on the same chemistry, where the terminal chlorine is displaced by an amine-bearing side chain. The compound is therefore described as an intermediate rather than an active substance: it does not itself have pharmacological activity, and its commercial importance comes from the structural fragment it installs.
Agrochemical intermediates. The terminal chloroalkyl chain and the amide or ketone formed from it are useful motifs in crop-protection chemistry, including carbamate-type and related active ingredients. As with the pharmaceutical applications, the compound is used as a building block in registered manufacturing processes rather than as a formulated product.
Organic synthesis generally. As an acylating agent it converts alcohols and amines into the corresponding esters and amides, and it is used to prepare substituted cyclopropyl ketones, substituted pyrrolidinone-type heterocycles and other ring systems through intramolecular reactions. Synthetic chemists value it specifically because a single reagent introduces both a carbonyl group and a masked electrophilic carbon.
Polymer and rubber additives. Derivatives of 4-chlorobutyryl chloride have been used in the preparation of modifiers and functional additives for polymer and rubber systems, where the chloroalkyl end group can be used to attach the additive to a polymer backbone or to introduce reactive functionality. It also finds use in the synthesis of coatings and specialty surfactants intermediates where a reactive halogen is needed at the end of a short aliphatic chain.
Other fine chemicals. The compound is used in the manufacture of flavour and fragrance building blocks, in photographic and specialty chemicals, and as a reagent in the preparation of organophosphorus intermediates, all of which exploit the same acyl chloride reactivity.
Quality Control and Analytical Methods
Specifications for 4-chlorobutyryl chloride are enforced with a small, well-established set of methods, and a competent certificate of analysis will name each one.
Identity and purity by gas chromatography. Capillary GC with flame-ionisation detection is the standard method for assay and for the identification and quantification of related impurities such as 4-chlorobutyric acid, residual chlorinating-agent residues and higher-boiling by-products. Results are usually reported by area normalisation against an internal standard, and a chromatogram should accompany the certificate for pharmaceutical-grade lots.
Acid chloride content by titration. A weighed sample is hydrolysed under controlled conditions and the liberated acid is titrated with a standard volumetric solution, prepared and standardised in accordance with GB/T 601. The total hydrolysable chloride determination is a direct check on the integrity of the acid chloride function and complements the GC assay.
Water content by Karl Fischer titration. Water is determined according to GB/T 6283. Because the sample reacts with water, the Karl Fischer method must be applied with an appropriate solvent system and a validated procedure; the measured value represents free water present in the sample and is a sensitive indicator of packaging failure.
Colour, density and refractive index. These simple physical checks are used as rapid release tests: colour is compared with a standard colour scale, density is measured with a calibrated digital densimeter, and refractive index with an Abbe refractometer at controlled temperature. A refractive index or density outside the historical band for a given grade is a strong signal that the lot has picked up moisture or contains a different isomer distribution.
Trace metals. Iron and other metals are measured by inductively coupled plasma optical emission spectrometry or atomic absorption spectrometry, often after dissolution of a hydrolysed sample. Iron limits deserve attention because iron can catalyse degradation during storage.
Sampling. Sampling follows general chemical-product rules (GB/T 6678) but must be conducted in a dry, well-ventilated environment with protective equipment, because the vapour is a lachrymator and the liquid is corrosive. Samples should be taken into dry, sealed containers that are filled as far as possible to exclude headspace moisture.
Safety, Storage, Transport and Regulatory Status
Hazard classification. 4-Chlorobutyryl chloride is a corrosive liquid. Under the GHS/CLP framework, acyl chlorides of this type carry hazard statements for severe skin burns and eye damage, and the substance is also a respiratory irritant and a strong lachrymator. It reacts with water and moisture releasing hydrogen chloride, so the hazard profile combines corrosivity with reactivity. The applicable pictograms are the corrosion pictogram and, where classified, the acute-toxicity or irritation pictogram; the SDS is the authoritative source of the exact classification applied in each jurisdiction.
Fire and thermal behaviour. The material is a combustible liquid with a flash point well above normal ambient temperatures, so the dominant risk is not vapour ignition at room temperature but the generation of irritant and corrosive hydrogen chloride if the material is heated or involved in a fire. Decomposition on heating is also a reason to keep distillation temperatures as low as the process allows.
Transport. Corrosive acyl chlorides are transported under hazard class 8 in the UN Model Regulations and in the ADR/IMDG frameworks, in packaging approved for corrosive liquids and with the shipper's declared proper shipping name, UN entry and packing group shown on the transport document. Because these substances are sensitive to water, they must be protected from rain, spray and humidity during handling and must not be stowed with alkalis or other incompatible cargo.
Storage. Store in a cool, dry, well-ventilated, fire-resistant area away from heat, direct sunlight, water, aqueous solutions, alcohols, amines, alkalis and oxidising agents. Keep containers closed and, where the operation permits, under a dry nitrogen blanket. Use secondary containment that is resistant to acid chlorides, and keep spill kits and suitable absorbent material available. Do not store the material in galvanised or unlined carbon-steel drums where hydrogen chloride attack is possible.
Engineering and personnel controls. Handle in a fume hood or under local exhaust ventilation with corrosion-resistant ducting, and draw air from low level because the vapour is heavier than air. Recommended personal protective equipment includes chemical splash goggles with a face shield, an acid-resistant apron or suit, and gloves made from a material suitable for acid chlorides. Eye wash facilities and safety showers should be immediately accessible, and any skin or eye contact requires immediate, prolonged irrigation and medical attention. Protective equipment must be inspected before use because hydrogen chloride degrades many materials.
Regulatory status. The substance is registered under the REACH framework in the EU and is listed on the TSCA Inventory in the United States for industrial and intermediate uses. Safety data sheets are prepared following the ISO 11014 convention and its national equivalents. Downstream users in the pharmaceutical sector additionally manage it under their own quality systems, where the material is treated as a starting material whose specification, supplier qualification and change control are documented.
Procurement and Acceptance Notes
A useful purchase specification for 4-chlorobutyryl chloride states the assay method and the minimum assay, the appearance and colour limit, the water limit, the total hydrolysable chloride or acid value, the iron and heavy-metal limits, the packaging type and net weight, and the storage statement. Because the material is readily hydrolysed, the specification should also state the required headspace or nitrogen blanketing practice and the maximum time between production and delivery, since ageing in a warm warehouse degrades a good lot.
At goods-in inspection, verify that the drum is intact and that the closure and gasket are undamaged, that the liner is not corroded, and that the liquid is clear and within the colour band for the grade. Confirm the lot number, the assay method used, the water result and the transport documents. Re-test water content and GC assay on receipt for pharmaceutical-grade lots, and record the opening date on partly used containers. Confirm that the SDS reflects the current hazard classification and that the shipping documents carry the correct class 8 designation, because an incorrect transport classification is the most common documentation defect with corrosive acyl chlorides.
FAQ
Q: What is the CAS number and molecular formula of 4-chlorobutyryl chloride?
The CAS registry number is 4635-59-0, the EINECS/EC number is 225-059-1, and the molecular formula is C4H6Cl2O with a molecular weight of 140.99 g/mol.
Q: What does 4-chlorobutyryl chloride look like and how does it behave with water?
It is a colourless to pale yellow liquid with a pungent, lachrymatory odour and a density of about 1.26 g/cm3. It hydrolyses readily in water, releasing hydrogen chloride and forming 4-chlorobutyric acid, which is why it must always be stored dry and sealed.
Q: What is the main industrial use of 4-chlorobutyryl chloride?
Its principal use is as a pharmaceutical intermediate. Acylation of a fluorobenzene ring gives 4-chloro-4'-fluorobutyrophenone, the precursor of the butyrophenone antipsychotic haloperidol, and the same chemistry supports other butyrophenone-type intermediates.
Q: How is the purity of 4-chlorobutyryl chloride determined?
Assay and related impurities are measured by capillary gas chromatography. Supporting methods include titration of the acid released on hydrolysis using standard volumetric solutions prepared per GB/T 601, water content by Karl Fischer titration per GB/T 6283, and refractive index or density as rapid release checks.
Q: How should 4-chlorobutyryl chloride be stored and packed?
Store it cool, dry and dark in a well-ventilated area away from water, alcohols, amines, alkalis and oxidising agents. It is supplied in sealed polyethylene-lined steel drums or intermediate bulk containers, typically 200-250 kg net, and containers should be kept closed and, where possible, under a dry inert gas blanket.
Q: What hazard class applies when it is shipped?
Corrosive acyl chlorides are shipped under hazard class 8 in the UN Model Regulations and the ADR/IMDG frameworks, in packaging approved for corrosive liquids and with the declared proper shipping name, UN entry and packing group shown on the transport documents.
Q: Is 4-chlorobutyryl chloride the same as 4-chlorobutyric acid?
No. 4-Chlorobutyryl chloride is the acid chloride (CAS 4635-59-0), a water-reactive, corrosive liquid used as an acylating agent. 4-Chlorobutyric acid is the free carboxylic acid formed when the acid chloride hydrolyses; it is a solid, far less reactive material with a different specification and shipping classification.





