JP-TS Aviation Fuel CAS 64742-47-8: Properties and Quality Control

May 09, 2025 Leave a message

What Is JP-TS Aviation Fuel?

JP-TS aviation fuel, listed under CAS number 64742-47-8, is a kerosene-type turbine fuel produced from a hydrotreated light petroleum distillate. The designation stands for a thermally stable jet fuel grade: the refining sequence removes sulphur, nitrogen and unstable hydrocarbon species so that the fuel can survive the high temperatures found in the fuel system of a jet engine without forming gum, varnish or lacquer deposits on hot surfaces.

The same CAS number identifies the hydrotreated light distillate cut that forms the base of many kerosene jet fuels, so the material is a mixture of hydrocarbons rather than a single compound. Its composition is defined by boiling range and by the specification limits it must satisfy, not by a fixed molecular formula.

Chemical Identity and Composition

Property Typical description
CAS number 64742-47-8
Chemical type Hydrotreated light petroleum distillate, kerosene-type hydrocarbon mixture
Main constituents Branched and cyclic paraffins with a small fraction of aromatics
Sulphur Very low after hydrotreating
Water solubility Practically insoluble; free water must be kept out of the fuel system
Appearance Clear, bright, straw-coloured to water-white liquid

Because free water in a fuel tank can freeze and block filters, and can also feed microbial growth, the essentially non-miscible character of the fuel with water is an operational advantage rather than a limitation.

Physical Properties

Kerosene-type turbine fuels are specified as ranges. The figures below are representative of a hydrotreated light distillate of aviation quality and should be confirmed against the certificate of analysis for each lot.

Property Typical value
Density at 15 °C about 0.800 g/cm³
Initial boiling point roughly 160 °C, with the bulk of the fuel distilling between 200 °C and 250 °C
Final boiling point below 300 °C
Flash point, closed cup 38 °C or higher
Freezing point about -58 °C for low-temperature grades
Kinematic viscosity at -20 °C Low enough to ensure reliable pumping and atomisation in cold conditions
Net heat of combustion at least 42.8 MJ/kg
Thermal stability High; controlled by the hydrotreating step and verified by a jet fuel thermal oxidation test

Note that the freezing point is sometimes reported informally as a melting point. For a hydrocarbon mixture of this type the meaningful figure is the freezing point, which governs the lowest temperature at which the fuel can still be pumped and filtered in flight.

Why Thermal Stability and Cold Behaviour Matter

Hot-section deposits: fuel is used as a heat sink on modern aircraft, so it warms up before it is burned. A fuel with poor thermal stability oxidises in that service and deposits lacquer on heat exchangers and fuel nozzles.

Cold-start and altitude performance: the freezing point and low-temperature viscosity decide whether fuel can be pumped through filters at altitude, where tank temperatures fall well below zero.

Combustion quality: a controlled boiling range and low aromatic content give a steady flame, complete combustion and predictable engine performance.

Safety on the ground: the flash point limit of 38 °C or higher keeps the fuel out of the most easily ignited class during storage and refuelling.

Quality Control and Test Methods

Aviation fuels are released only against an agreed specification, and the buyer should expect the full test slate with each lot. Kerosene-type turbine fuel is commonly checked against ASTM D1655 for Jet A and Jet A-1, and against the equivalent defence specification, DEF STAN 91-091, for Jet A-1. The routine test slate covers:

Distillation range by ASTM D86, which fixes the light and heavy ends of the cut.

Flash point by ASTM D93, closed cup, for flammability control.

Freezing point by ASTM D2386, for low-temperature operability.

Density by ASTM D1298 and kinematic viscosity by ASTM D445.

Net heat of combustion by ASTM D4809, which sets the energy available per kilogram.

Acidity by ASTM D3242 and thermal oxidation stability by ASTM D3241, the jet fuel thermal oxidation test.

Particulate and free water by ASTM D5452 or ASTM D2276, plus visual clarity.

Thermal stability is the test that most clearly distinguishes a thermally stable grade from an ordinary kerosene cut, because it is run at elevated temperature and directly predicts the deposit-forming tendency of the fuel.

Fuel Handling, Storage and Distribution

Store in dedicated, clean steel tanks with water bottoms drained at regular intervals, and never mix aviation fuel with other petroleum products.

Filter the product during loading and before delivery, and monitor filter differential pressure as an indicator of contamination.

Keep the fuel dry: free water promotes icing and microbiological growth, so water content should be checked at receipt and before issue.

Use dedicated pumps, hoses and tankers that are not shared with other fuel types, and record every transfer.

Avoid excessive heating during storage; prolonged high temperature reduces thermal stability margin even when the flash point is respected.

Retain a sealed sample of each lot so that any quality question can be resolved against the original delivery.

Frequently Asked Questions

Q: What does JP-TS stand for?
It designates a jet propulsion fuel grade specified for thermal stability. The thermally stable property is achieved by hydrotreating the distillate so that deposit-forming species are removed before the fuel reaches the engine.

Q: What is CAS 64742-47-8?
It is the registry number for a hydrotreated light petroleum distillate, a kerosene-range stream. Several aviation and industrial kerosene fuels are based on this type of cut, and the finished fuel is defined by its specification limits rather than by the CAS number alone.

Q: Why is the freezing point more important than a melting point?
A turbine fuel is a mixture of hydrocarbons and does not melt at one temperature. The freezing point describes the temperature below which wax crystals begin to form and can block filters, which is the property aircraft operators actually need to know.

Q: Which specifications apply?
Jet A and Jet A-1 are normally bought against ASTM D1655, and Jet A-1 also against DEF STAN 91-091. Individual airlines may add their own limits on top of these documents.

Q: How is thermal stability tested?
By the jet fuel thermal oxidation test under ASTM D3241, in which the fuel is pumped across a heated tube and the deposit formed on the tube is rated against a reference scale.

Q: How should aviation fuel be stored?
In dedicated clean tanks with regular water draining, filtration on receipt and issue, and strict separation from other petroleum products. Records of every transfer and a retained sample for each lot make it possible to trace any quality issue.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry