4-Methyl-2-pentanone (CAS 108-10-1), almost always called methyl isobutyl ketone or MIBK, is a colourless ketone with a mild odour and a medium evaporation rate. The molecule is a simple branched aliphatic ketone, but the branching does useful work. It keeps the solvent in a drying film long enough for the coating to level and release air, while still evaporating quickly enough for industrial line speeds, and it dissolves a broad range of resins without the aggressiveness of faster ketones such as acetone.
Identity and Key Physical Properties
| Parameter | Typical value |
|---|---|
| CAS number | 108-10-1 |
| Molecular formula | C6H12O |
| Molar mass | 100.16 g/mol |
| Boiling point | 116-118 C |
| Flash point | about 14 C, closed cup |
| Autoignition temperature | about 448 C |
| Explosive limits in air | 1.2-8.0 percent by volume |
| Relative density | about 0.80 at 20 C |
| Water solubility | about 1.9 g per 100 mL at 20 C |
| Vapour pressure | about 2 kPa at 20 C |
Solvent for Paints, Coatings and Printing Inks
MIBK is a mid-range solvent in the evaporation ladder, sitting between fast ketones and slower esters and glycol ethers. It dissolves acrylic, alkyd, epoxy, nitrocellulose, vinyl and polyurethane resins, holds pigment dispersions stable, and controls the drying profile so that a film levels properly instead of skinning over too quickly and leaving brush marks, orange peel or trapped solvent. In two-component industrial coatings it also helps the second component disperse evenly, which improves the uniformity of the cured film.
In printing, MIBK gives flexographic and gravure inks the flow they need to pass through the press at speed, producing sharp text and clean halftones on paper, board, film and foil. It also promotes adhesion of the ink to the substrate, which improves resistance to rubbing and to later converting steps.
Adhesives, Sealants and Viscosity Control
Adhesive formulators use MIBK to adjust viscosity and open time. It is a common solvent for polyurethane, neoprene and other rubber-based contact adhesives, laminating adhesives and sealants, because it keeps the polymer in solution at a workable solids content and then releases steadily after the joint is closed. The same property is used to reactivate dried adhesive films before bonding, and to clean adhesive residue from application equipment.
Cleaning, Degreasing and Extraction Duties
The strong solvency of MIBK makes it a workhorse in industrial cleaning. It removes grease, oil, wax, ink and adhesive residue from machined parts, print rollers, mixing vessels and tooling, and it does so without attacking most metals, which keeps it useful where a chlorinated solvent would raise corrosion or regulatory concerns.
Two less obvious duties are worth noting. MIBK is used to dewax lubricating oil streams: the solvent dissolves the wax so that it can be separated from the oil by cooling and filtration, improving the low-temperature behaviour of the finished lubricant. It is also used in hydrometallurgical separation, most notably in the extraction of tantalum from niobium in fluoride-containing solutions, a classic solvent extraction route in speciality metals refining.
Chemical Intermediate and Laboratory Use
MIBK is more than a solvent; it is also a synthesis intermediate. Hydrogenation converts it into 4-methyl-2-pentanol, also known as methyl isobutyl carbinol, which is used as a frother in mineral flotation and as a solvent in its own right. MIBK itself is used in laboratory extraction and purification work, where its limited water solubility and good selectivity for organic solutes make it easy to separate from an aqueous phase, and it appears as a raw material in the manufacture of fine chemicals and antioxidant additives.
Industrially, MIBK is produced from acetone in a single reactor over a bifunctional catalyst. The acetone first condenses to diacetone alcohol, which is dehydrated to mesityl oxide and then hydrogenated to MIBK, so one cheap feedstock delivers the whole molecule.
Specification, Safety and Storage
Commercial MIBK is normally specified at 99.5 percent purity or higher by gas chromatography, with low water, low acidity and a pale colour. Water content is commonly measured by Karl Fischer titration following ASTM D1364, and the acetone and mesityl oxide levels are controlled because they shift the evaporation profile of a coating. Grade selection also depends on whether the end use is coatings, extraction or pharma-related synthesis.
Safety practice follows directly from the flash point of about 14 C: MIBK is a flammable liquid at ordinary room temperature, so storage areas need bonding and grounding, flameproof electrical equipment, and no ignition sources nearby. Drums should be kept closed under a nitrogen blanket in a cool, well-ventilated place away from direct sun. Because the vapour can cause headache, dizziness and narcotic effects at high concentration, local exhaust ventilation and respiratory protection are used where open handling cannot be avoided.
Frequently Asked Questions
Q: What is 4-methyl-2-pentanone used for?
It is used mainly as a medium-evaporating solvent for paints, coatings, printing inks, adhesives and industrial cleaning, and also as an extraction solvent, a dewaxing solvent and an intermediate for other chemicals.
Q: Is MIBK the same as MEK?
No. MEK is 2-butanone, a faster evaporating ketone, while MIBK is 4-methyl-2-pentanone. MIBK evaporates more slowly and has a higher boiling point, which gives better film levelling.
Q: Why is MIBK preferred over faster solvents in coatings?
Its slower evaporation keeps the film open long enough for brush and spray marks to flow out and for trapped solvent to escape, which reduces defects such as orange peel, pinholing and dry spray.
Q: What is the flash point of MIBK and how does it affect storage?
The closed cup flash point is about 14 C, so the liquid is flammable at normal room temperature. Tanks and drums need grounding and bonding, flameproof equipment and strict separation from ignition sources.
Q: How is MIBK produced industrially?
Acetone is converted in one reactor over a bifunctional catalyst: aldol condensation gives diacetone alcohol, dehydration gives mesityl oxide, and hydrogenation of the double bond gives MIBK.
Q: Is MIBK miscible with water?
No. It has limited water solubility of about 1.9 g per 100 mL at 20 C, so it forms a separate organic phase in most aqueous systems, which is exactly what makes it useful in extraction and purification.





