Identity and Physical Properties
2-Butanone, also called methyl ethyl ketone (MEK), is a symmetric aliphatic ketone with CAS number 78-93-3, formula C4H8O and molecular weight 72.11 g/mol. It is a colourless, mobile liquid with a sharp acetone-like odour, a density of 0.805 g/cm³ at 20 °C, a boiling point of 79.6 °C, a melting point of −86.3 °C and a vapour pressure of about 10.5 kPa at 20 °C. It is miscible with ethanol, ether, acetone, benzene and most other organic solvents, and it is appreciably water-soluble at roughly 275 g/L at 20 °C - a property that separates it from most hydrocarbon solvents and drives much of its industrial value.
The molecule is a medium-polarity solvent with a hydrogen-bond acceptor only, so it dissolves both polar resins and many non-polar polymers. It has the typical ketone reactions: condensation with hydroxylamine and hydrazines to give oximes and hydrazones, addition with hydrogen cyanide, reduction to 2-butanol and catalytic oxidation to diacetyl or acetic acid depending on conditions.
Specification and Test References
| Parameter | Typical value | Test reference |
|---|---|---|
| Assay (mass) | ≥ 99.5 % | ASTM D740 |
| Water | ≤ 0.15 % w/w | ASTM D740 / ASTM D1364 |
| Colour | ≤ 10 Pt-Co units | ASTM D1209 |
| Non-volatile matter | Low, typically ≤ 0.005 g/100 mL | ASTM D1353 |
| Density at 20 °C | 0.801–0.805 g/cm³ | ASTM D4052 |
| Distillation range | 78–81 °C | ASTM D1078 |
| Flash point | about −9 °C, closed cup | ASTM D93 |
| Autoignition temperature | about 404 °C | Literature value |
| Transport classification | UN 1193, Class 3, Packing Group II | UN Model Regulations |
The two specification numbers that cause most disputes are water and non-volatile residue. Water above limit produces haze, slows solvent release and can hydrolyse moisture-sensitive resins and isocyanates. Non-volatile residue, even at a few hundredths of a gram per 100 mL, leaves films and fisheyes in thin-film coatings and contaminates electronic cleaning baths.
Principal Uses
Coating solvent demand is the largest single outlet. MEK dissolves nitrocellulose, acrylic, vinyl, alkyd, epoxy and polyurethane resins and is used in lacquers, wood finishes, printing inks, thinners and aerosol formulations, where its balanced evaporation rate gives good flow without long tack. It is a standard component of solvent-borne adhesive systems for rubber and resin-based adhesives, giving the dried film flexibility and open time in shoe, leather and packaging applications.
As a chemical intermediate, 2-butanone is converted to 2-butanol by hydrogenation and to methyl ethyl ketone peroxide by reaction with hydrogen peroxide, the latter used as a room-temperature curing initiator for unsaturated polyester, vinyl ester and acrylic resins. It also appears in the synthesis of fine chemicals, including flavour and fragrance components and pharmaceutical intermediates, where its clean condensation chemistry is an advantage. Other uses include dewaxing of lubricating oil fractions and the extraction of selected natural products.
Fire, Exposure and Storage Controls
The flash point near −9 °C means MEK is flammable at essentially every practical working temperature, with an explosive vapour range of about 1.4 to 11.4 % by volume and vapour heavier than air. Controls are uncompromising: earthing and bonding of all transfer equipment, explosion-proof electricals and instrumentation in classified areas, closed-loop or ventilated transfer, elimination of hot work and of non-rated tools, and prohibition of smoking in the storage area. Containers are kept closed when not in use, and spray or dipping operations with large open surfaces are ventilated to keep vapour well below the lower flammable limit.
On exposure limits, a permissible exposure limit of 200 ppm as an 8-hour time-weighted average with a short-term value of about 300 ppm is applied in United States workplaces, with the same figures used as guideline values in many other jurisdictions; the immediately dangerous concentration is 3000 ppm. Inhalation is the main route, and MEK is also absorbed through skin. Health effects of overexposure include headache, dizziness, narcosis and eye and respiratory irritation, and repeated skin contact defats and dries the skin. Local exhaust ventilation at filling, spraying and drying points, together with chemical goggles, gloves and respiratory protection for confined space work, forms the standard control package.
Storage is in closed drums or tanks in a cool, well-ventilated place away from heat, sparks, open flame, strong oxidisers, peroxides and strong acids and bases. Small quantities are held in approved flammable liquid cabinets; bulk parcels are earthed and, where long-distance transport is involved, meet the UN 1193 Class 3 Packing Group II classification. Purity drift in storage is limited by keeping containers closed, since MEK absorbs moisture from humid air and the resulting water content is the most common out-of-specification finding on aged stock.
Frequently Asked Questions
Q: What is the CAS number and formula of 2-butanone?
A: 2-Butanone, also called methyl ethyl ketone, is CAS 78-93-3 with the formula C4H8O and a molecular weight of 72.11 g/mol.
Q: What are the main commercial uses of MEK?
A: Coatings, thinners, printing inks and adhesives are the largest uses. It is also converted to 2-butanol and to methyl ethyl ketone peroxide, used as a curing initiator for unsaturated polyester and vinyl ester resins.
Q: Why is the flash point a critical safety number?
A: The closed-cup flash point is about −9 °C, so the material forms a flammable vapour-air mixture at ordinary working temperatures. Earthing, bonding, explosion-proof equipment and ventilation are mandatory rather than optional.
Q: What exposure limits apply to MEK in the workplace?
A: A permissible exposure limit of 200 ppm as an 8-hour time-weighted average, with short-term exposure around 300 ppm, is widely applied, and 3000 ppm is the immediately dangerous level.
Q: Is 2-butanone soluble in water?
A: Yes, roughly 275 g/L at 20 °C, though it is used mostly in solvent blends with other organic solvents. Its water solubility means humid air can raise the water content of an open container over time.
Q: What is the difference between 2-butanone and methyl ethyl ketone?
A: They are the same substance. 2-Butanone is the systematic name and methyl ethyl ketone is the retained common name used in most commercial documents and in transport paperwork.





