Three Major Categories of Flame Retardants: A Technical Guide

Mar 26, 2025 Leave a message

How Flame Retardants Are Classified

Flame retardants are rarely traded as a single generic commodity. They are a family of functional additives and reactive monomers selected according to the polymer they must protect, the fire test the finished article has to pass, and the regulatory regime of the market where the article is sold. Suppliers and formulators therefore sort the family in three different ways at the same time: by the active element that does the chemistry, by whether the product is added physically or built into the polymer chain, and by whether the product is an inorganic or an organic compound. Understanding all three axes is essential, because the same substance is described differently depending on which axis a buyer is using.

This guide sets out the three major categories in detail, together with the mechanisms, typical loading levels, test methods and regulatory constraints that determine which category is appropriate for a given application.

Category One: Classification by Flame-Retardant Element

The first and most common classification groups products by the element responsible for the flame-retarding action. The main families are halogen, phosphorus, nitrogen, sulfur, phosphorus-halogen, phosphorus-nitrogen, silicon, antimony, boron, and the aluminium-magnesium group based on metal hydroxides. Halogenated products remain the largest single family in volume terms because they achieve a given fire performance at low addition levels, which keeps the mechanical and processing properties of the base polymer largely intact.

Family Representative chemistry CAS example Principal mechanism Typical host polymers
Brominated Tetrabromobisphenol A (C15H12Br4O2, MW 543.9) 79-94-7 Gas-phase radical scavenging by HBr Epoxy laminates, ABS, HIPS
Brominated Decabromodiphenyl ethane 84852-53-9 Gas-phase radical scavenging Polyolefins, engineering plastics
Chlorinated Tris(2-chloroisopropyl) phosphate 13674-84-5 Gas-phase plus condensed-phase char Rigid and flexible polyurethane foam
Phosphorus Triphenyl phosphate (C18H15O4P, MW 326.3) 115-86-6 Condensed-phase char promotion PVC, engineering plastics, foams
Phosphorus Red phosphorus 7723-14-0 Condensed-phase acid catalysis Glass-filled polyamides, PBT
Phosphorus Ammonium polyphosphate 68333-79-9 Intumescent acid source Coatings, polyolefin intumescent systems
Nitrogen Melamine (C3H6N6, MW 126.1) 108-78-1 Endothermic sublimation, inert gas dilution Rigid polyurethane foam, polyamides
Nitrogen Melamine cyanurate (C6H9N9O3, MW 255.2) 37640-57-6 Char and vapour-phase dilution Unfilled polyamides
Antimony Antimony trioxide (Sb2O3, MW 291.5) 1309-64-4 Synergist forming volatile antimony halides Used with halogenated products
Aluminium-magnesium Aluminium hydroxide (Al(OH)3, MW 78.0) 21645-51-2 Endothermic dehydration, water release Cable compounds, rubber, thermosets
Aluminium-magnesium Magnesium hydroxide (Mg(OH)2, MW 58.3) 1309-42-8 Endothermic dehydration at higher temperature Polyolefin cable compounds
Boron Boric acid and zinc borates 10043-35-3 (boric acid) Glass or char formation, smoke suppression PVC, polyolefins, elastomers

Category Two: Additive and Reactive Types

The second classification looks at how the product is put into the material. Additive flame retardants are compounded into the polymer before processing and remain dispersed as a separate physical phase. They are easy to handle, available in a wide range of particle sizes and forms, and account for the large majority of the market because they can be introduced at the compounding stage without changing the polymerisation route. Their drawback is that a high loading of a foreign phase dilutes the matrix: tensile strength, elongation, impact resistance and melt flow can all fall, and in fibre or thin-wall applications the loss of processability becomes the limiting factor.

Reactive flame retardants carry functional groups that take part in the polymerisation or curing reaction, so the flame-retardant element becomes part of the polymer backbone or network. The advantages are a durable effect that does not migrate, no plasticising of the matrix, and better retention of mechanical properties and transparency. The disadvantages are practical: the monomer must be compatible with the reaction chemistry, it often must be introduced at the plant rather than at the converter, and the range of commercially available products is narrower. Reactive types are therefore concentrated in thermosetting systems such as epoxy laminates, unsaturated polyester and rigid polyurethane foam, and are the smaller share of total consumption.

Some products can act in both roles. Brominated bisphenol A derivatives, for example, are used as reactive monomers in laminate resins and also as additive flame retardants in thermoplastic compounds, and certain phosphorus-containing polyols behave the same way in polyurethane foam. For the buyer the practical consequence is that the data sheet must state explicitly whether the product is intended for reactive incorporation or for compounding, because the two grades are not interchangeable and their specifications differ in hydroxyl value, viscosity, moisture content and colour.

Category Three: Inorganic and Organic Compounds

The third classification separates inorganic from organic compositions. Inorganic flame retardants include the metal hydroxides, antimony trioxide, boron compounds, red phosphorus and intumescent mineral systems. They are characterised by high thermal stability, low volatility, non-toxicity in most cases, absence of corrosive gas evolution, smoke suppression and long-lasting effect. Their weakness is the loading level required: metal hydroxides typically have to be added at 50% or more by weight to reach a meaningful fire performance, which has a serious effect on processing viscosity, elongation and electrical properties of the compound.

Organic flame retardants include the brominated, chlorinated and organophosphorus families. They are effective at much lower loadings, usually between a few percent and about twenty percent, and are therefore preferred where mechanical performance and processing characteristics must be preserved. The trade-off is their behaviour in a fire: halogenated products produce hydrogen halide gases that are corrosive and toxic, and can increase smoke density. Halogen-free organophosphorus products avoid the hydrogen halide problem but often require a higher loading than halogenated systems and may plasticise the polymer.

Halogenated Systems and the Antimony Synergist

In a brominated system the flame-retarding action is largely physical and gas-phase. On heating, the brominated compound releases hydrogen bromide, which intercepts the high-energy hydroxyl and hydrogen radicals that propagate the combustion chain, converting them into species that are far less reactive. In a chlorinated system the same radical-scavenging chemistry operates through hydrogen chloride, but the carbon-chlorine bond is stronger than the carbon-bromine bond, so chlorinated products are effective at lower temperatures and generally need a higher loading or a synergist to match a brominated system.

Antimony trioxide is the classic synergist. It is not an effective flame retardant on its own; used with a halogenated product it forms volatile antimony halides that act in the vapour phase and allow the halogen loading to be reduced substantially. This synergism applies to aliphatic and aromatic brominated compounds but is much weaker with decabromodiphenyl ether and decabromodiphenyl ethane, which act mainly in the condensed phase. Because antimony trioxide carries its own hazard classification and adds opacity and density to the compound, several markets have moved towards phosphorus-based alternatives, and some specifications now exclude antimony entirely.

Halogenated flame retardants remain important because their efficacy per unit weight is unmatched, but their regulatory position has tightened considerably. Certain brominated diphenyl ethers and chlorinated paraffins are restricted or banned, and the industry has responded by moving to high-molecular-weight brominated polymers that are too large to be bioavailable, and to phosphorus and nitrogen systems where the fire test and the processing window allow.

Phosphorus, Nitrogen and Intumescent Systems

Phosphorus-based products work mainly in the condensed phase. On heating they decompose to acidic species, in particular phosphoric and polyphosphoric acids, which catalyse dehydration and cross-linking of the polymer and promote formation of a carbonaceous char. The char acts as a thermal barrier, slowing the rate at which volatile fuel reaches the flame, and it also limits oxygen access. Red phosphorus, phosphates, phosphonates and phosphinates all operate on this principle, with the optimum choice depending on the processing temperature of the host polymer and its chemistry.

Nitrogen-containing products act in several ways at once: melamine sublimes endothermically, absorbing heat and diluting the vapour phase with inert gas, while its decomposition products can promote char formation. The combination of phosphorus and nitrogen is more effective than either element alone, and it is the basis of intumescent systems that swell into a thick insulating foam. A typical intumescent formulation contains an acid source such as ammonium polyphosphate, a carbon source such as a polyol or pentaerythritol, and a blowing agent such as melamine, together with a binder. Intumescent coatings for structural steel and cable trays rely on this mechanism, since the expanded layer can insulate a substrate for the period required by the relevant fire resistance test.

Metal Hydroxide Fillers and Loading Levels

Aluminium hydroxide and magnesium hydroxide act by endothermic decomposition, releasing water vapour that cools the substrate and dilutes the combustible gases, while the residual metal oxide forms a protective ceramic-like layer. Aluminium hydroxide begins to decompose at around 180 to 220 C, which suits polymers processed below about 200 C such as EVA-based cable compounds, flexible PVC and rubber. Magnesium hydroxide decomposes at roughly 330 C, making it the choice for polypropylene and other engineering thermoplastics processed at higher temperatures, although its higher cost and slightly lower efficiency per unit mass are acknowledged limitations.

Because the mechanism is endothermic, the loading matters more than the identity of the product: to absorb enough heat, the filler usually has to be present at 50% or more by weight. Achieving that loading requires surface-treated, fine-particle grades with low moisture content to avoid processing problems and to retain elongation. Formulators therefore specify particle size distribution, surface treatment chemistry, moisture content and pH alongside the assay, and buy the material as a compounding filler rather than as a simple chemical.

How Flame Retardant Performance Is Measured

Performance claims must be tied to a test. The most widely referenced screening test for plastics is the vertical and horizontal burning test specified in UL 94 and in the equivalent IEC 60695-11-10, which classifies a specimen by its burning rate and self-extinguishing behaviour. Limiting oxygen index, determined under ASTM D2863, ISO 4589 or GB/T 2406, expresses the minimum oxygen concentration in a nitrogen-oxygen atmosphere that will support candle-like burning of the specimen, and is a useful comparative measure of difficulty of ignition. GB/T 2408 covers horizontal and vertical burning of plastics for the domestic market.

Test Standard reference What it reports Typical use
Vertical burning of plastics UL 94 / IEC 60695-11-10 Afterflame time, dripping, class V-0, V-1, V-2 Screening of compounded thermoplastics
Horizontal and vertical burning GB/T 2408 Burning rate and self-extinguishing behaviour Domestic plastics qualification
Limiting oxygen index ASTM D2863 / ISO 4589 / GB/T 2406 Minimum oxygen concentration supporting combustion Comparative ranking of formulations
Heat release rate ISO 5660 cone calorimeter Peak and total heat release, ignition time, smoke Development and fire modelling
Surface burning characteristics ASTM E84 Flame spread and smoke developed indices Building materials and cable trays

A single screening result is not a fire-safety certificate. A formulation that reaches a given class in a small-scale vertical burning test may behave differently at full scale, where heat release rate, smoke production, toxicity of combustion products and the interaction with the surrounding construction all matter. Serious projects therefore pair a screening test with cone calorimeter data and, where the application is regulated, with the specific test required by the building code or product standard for that end use.

Regulatory Status and Substitution Pressure

The choice of category is now driven as much by regulation as by fire performance. In the European Union, RoHS restricts polybrominated biphenyls and polybrominated diphenyl ethers in electrical and electronic equipment, and the persistent organic pollutants regulation implements the listings agreed under the Stockholm Convention, which include hexabromocyclododecane, CAS 25637-99-4, and decabromodiphenyl ether, CAS 1163-19-5. REACH restrictions additionally limit certain chlorinated phosphates in articles intended for children, and a number of flame retardants appear on the candidate list of substances of very high concern, which triggers information duties along the supply chain.

In the United States, flame retardant use in consumer products is governed mainly by state-level furniture and electronics flammability rules together with the federal Toxic Substances Control Act inventory requirements. In China, chemical flame retardants are managed as hazardous or general chemicals according to their classification, with production and transport licensing where applicable, and articles must comply with the applicable national standards for the end product.

Substitution pressure has three practical consequences for buyers. First, the halogenated products with the best efficacy-to-cost ratio are increasingly the ones under restriction, so approved formulations must be re-qualified rather than simply sourced from a different producer. Second, non-halogenated alternatives usually require a higher loading, which changes the mechanical and electrical data of the compound and often requires re-testing of the finished article. Third, because the restricted substances are regulated by CAS number, a specification written around a chemical name without a CAS number is difficult to enforce; purchase documents should always identify the flame retardant by CAS number and by the intended polymer system.

Selection and Purchasing Checklist

Selecting a flame retardant is a system decision rather than a catalogue decision. Start from the end-use test the article must pass, then fix the host polymer and its maximum processing temperature, and only then choose the family. A phosphorus-based product that decomposes below the extrusion temperature will fail in the extruder rather than in the fire test, and a metal hydroxide chosen for a low-temperature compound will be unsuitable for a polyamide processed above 280 C.

For each candidate, verify the CAS number, the assay or active content, the decomposition or melting range, the moisture content, the particle size or physical form, and the recommended loading range. Confirm the hazard classification and the transport entry, and request the safety data sheet prepared to ISO 11014 together with any substance registration status required in the destination market. For metal hydroxide fillers, also check the surface treatment and the resulting elongation of the test compound, because the same nominal grade can behave very differently depending on how the particles were coated.

Finally, define acceptance testing before the first delivery. Agree on the identity check, the assay method, the moisture limit and the retention sample period, and specify how a batch that fails a performance test is to be handled. Because flame retardants are almost always used at high loading, a small deviation in active content or particle size has a large effect on the finished compound, and the cost of a disputed batch is much higher than the cost of defining the acceptance criteria in the first place.

FAQ

Q: What are the three major categories of flame retardants?
They are classified in three parallel ways: by the flame-retardant element or element combination, by whether they are additive or reactive, and by whether they are inorganic or organic compounds.

Q: What is the difference between additive and reactive flame retardants?
Additive products are compounded into the polymer as a dispersed phase and dominate the market because they are easy to use, while reactive products contain functional groups that bond into the polymer network during curing, giving a more durable effect with better retention of mechanical properties, mainly in thermosets.

Q: How do halogenated flame retardants work?
They release hydrogen halide in the heated zone, and the halogen radicals intercept the chain-propagating radicals in the flame. Their effect is often boosted by antimony trioxide, CAS 1309-64-4, which forms volatile antimony halides and allows the halogen loading to be reduced.

Q: Why are metal hydroxides used at such high loadings?
Aluminium hydroxide, CAS 21645-51-2, and magnesium hydroxide, CAS 1309-42-8, work by endothermic decomposition and water release rather than by radical chemistry, so 50% or more by weight is usually needed to absorb enough heat, which in turn affects the mechanical and processing properties of the compound.

Q: Which tests are used to prove flame retardant performance?
Typical screening tests are the vertical burning classification of UL 94 and IEC 60695-11-10, limiting oxygen index by ASTM D2863, ISO 4589 or GB/T 2406, horizontal and vertical burning of plastics under GB/T 2408, and heat release rate by cone calorimeter under ISO 5660.

Q: Why has the choice of flame retardant become a regulatory question?
Because several halogenated products are restricted under RoHS, the Stockholm Convention on persistent organic pollutants and REACH, so an approved formulation may not simply be re-sourced from another producer, and specifications should identify the substance by CAS number and the intended polymer system.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry