Methyl Methacrylate Monomer: Chemical Identity and Commercial Position
Methyl methacrylate (MMA, CAS 80-62-6) is an unsaturated ester and the principal monomer behind poly(methyl methacrylate) (PMMA) and a broad family of acrylic copolymers. Under ambient conditions it is a clear, colourless liquid with a sharp, recognisable ester odour. Bulk buyers source it in 190 kg drums, intermediate bulk containers and ISO tank containers, and the commodity is declared under HS code 2916130010.
The molecule carries both a vinyl group and an ester group. That dual functionality allows it to take part in free-radical addition polymerisation and in transesterification, which is why MMA sits at the centre of the acrylic value chain rather than at its edge: cast sheet, moulding compound and acrylic emulsion all begin with this one intermediate.
Typical Physical and Chemical Properties
The table summarises the values most often requested on a technical data sheet or in import documentation for standard inhibited monomer grades.
| Property | Typical value |
|---|---|
| CAS number | 80-62-6 |
| Purity | 99% minimum |
| Appearance | Clear, colourless liquid |
| Odour | Characteristic ester |
| Boiling point | 163 °C at atmospheric pressure |
| Melting point | 16 °C |
| Flash point | 77 °C |
| Density | 1.015 g/cm³ |
| Solubility | Soluble in common organic solvents; limited miscibility with water |
| HS code | 2916130010 |
| Packaging | 190 kg drum, intermediate bulk container, ISO tank |
Because the melting point is close to ordinary room temperature, cold-weather logistics deserve attention. At low ambient temperatures the monomer can begin to crystallise, and any solid phase must be remelted gently and homogenised before the drum is put into service.
Production Routes, Reactivity and Polymerisation
Two routes dominate commercial supply. The first is the three-step sequence that begins with acetone and hydrogen cyanide, proceeds through acetone cyanohydrin and yields a methacrylamide sulphate stream that is hydrolysed to methacrylic acid and then esterified with methanol. The second is a two-step route in which ethylene reacts with methanol to give methyl propionate, which is condensed with formaldehyde to form the ester. Both routes converge on the same molecule, and both produce a crude stream that must be distilled and inhibited before it is saleable, so feedstock economics for acetone, hydrogen cyanide, ethylene and methanol drive the monomer price far more than shifts in downstream demand.
MMA polymerises exothermically. Suspension, emulsion, bulk and solution processes all depend on tight control of initiator addition and reactor temperature, because an uncontrolled mass of monomer can liberate heat faster than a jacket can remove it. Consistent inhibitor level in the delivered drum is therefore a processing parameter, not a formality.
Downstream Applications and Copolymerisation
Cast and extruded PMMA sheet, including optical and signage grades
Suspension and bulk moulding compounds for lighting, appliances and profiles
Acrylic emulsions for architectural and industrial coatings
Copolymer additives that upgrade the processing behaviour of poly(vinyl chloride)
Specialty methacrylate esters produced by transesterification with higher alcohols
Adhesives, sealants, reactive resins and synthetic marble systems
In copolymer work, MMA is frequently combined with styrene and butadiene to make an additive that improves the processing and impact behaviour of poly(vinyl chloride) compounds. Transesterification with higher alcohols opens a second product family of specialty methacrylate monomers for coatings and reactive resins.
Storage, Packaging and Quality Control
Inhibited monomer should be kept away from heat, direct sunlight and oxidising agents, and stored in well-ventilated areas with the container headspace maintained as intended by the supplier. Inhibitor systems rely on dissolved oxygen to remain effective, so drums should not be routinely blanketed with inert gas without process advice from the producer.
Every consignment is normally supported by a certificate of analysis covering purity, colour, water content and inhibitor level, allowing the buyer to verify the batch against the purchase specification before releasing it to production. Sub-packaging and small batch shipment are practical for pilot lines and laboratory evaluation, while ISO tank supply suits continuous sheet and resin plants.
Frequently Asked Questions
Q: What is the CAS number of methyl methacrylate?
Methyl methacrylate monomer is registered under CAS 80-62-6.
Q: What is the boiling point of MMA?
The boiling point is 163 °C at atmospheric pressure.
Q: What is the flash point of methyl methacrylate?
The flash point is 77 °C, so the monomer is not classified as a low-flash solvent but still requires normal flammable-liquid controls.
Q: Why must MMA be stored carefully in cold weather?
The melting point is 16 °C, so the liquid can crystallise at low ambient temperature; the solid phase must be remelted gently and mixed before use.
Q: What is the density of methyl methacrylate?
Typical density is 1.015 g/cm³ at 20 °C.
Q: How is MMA shipped in bulk?
Standard packings are 190 kg drums, intermediate bulk containers and ISO tank containers, each with a batch certificate of analysis.





