What Is Dimethylacetamide (DMAc, CAS 127-19-5)?
Dimethylacetamide, systematically N,N-dimethylacetamide, is an amide solvent with the condensed formula CH3C(O)N(CH3)2, the molecular formula C4H9NO and a molar mass of 87.12 g/mol. It is abbreviated DMAc, and occasionally DMA. The molecule combines a polar carbonyl group with two methyl groups on the nitrogen, which makes it a dipolar aprotic solvent of high dielectric constant, roughly 37.8 at 25 °C, and of high boiling point.
Physical and Chemical Properties
| Property | Typical value |
| Chemical name | N,N-Dimethylacetamide (DMAc) |
| CAS number | 127-19-5 |
| Molecular formula | C4H9NO |
| Molar mass | 87.12 g/mol |
| Appearance | Colourless, transparent liquid |
| Odour | Faint, pungent or slightly ammoniacal |
| Melting point | about -20 °C |
| Boiling point | 164 to 166 °C at 101.3 kPa |
| Density | 0.937 g/cm³ at 25 °C |
| Refractive index | 1.4380 at 20 °C |
| Flash point | about 63 to 70 °C, method dependent |
| Viscosity | 0.92 mPa·s at 25 °C |
| Vapour pressure | about 0.17 kPa at 25 °C |
| Surface tension | about 34 mN/m at 20 °C |
| Explosive limits in air | 1.8% to 11.5% by volume |
Is Dimethylacetamide Soluble in Water?
Yes. DMAc is fully miscible with water in all proportions at ambient temperature; there is no phase separation and no practical solubility ceiling. The same applies to most oxygen- and nitrogen-containing organic solvents, including methanol, ethanol, isopropanol, acetone, ethers, esters, chlorinated solvents such as chloroform and dichloromethane, and aromatic solvents such as benzene and toluene. Miscibility with saturated aliphatic hydrocarbons is limited, which is one reason DMAc works well as a selective extraction solvent.
Two consequences follow from this behaviour. First, DMAc is hygroscopic: an open container will pick up atmospheric moisture, gradually changing both assay and water content, so drums should be kept sealed and headspace exposure minimised. Second, water is not an inert diluent in DMAc systems; acids or bases dissolved in the water phase accelerate hydrolysis of the amide, particularly at elevated temperature.
DMAc has good thermal stability and can be purified by distillation at atmospheric pressure or under vacuum, remaining stable at its boiling point under normal conditions, and it is stable in neutral aqueous solution for extended periods. Strong bases can saponify the amide and hot acid with an alcohol can promote alcoholysis, so process designers keep pH near neutral and avoid prolonged high-temperature contact with concentrated acids or alkalis. Because DMAc is a combustible, high-boiling liquid rather than a low-flash solvent, it is not easily stripped from a process stream, which is an advantage in spinning and casting but a complication in solvent recovery.
Industrial Applications of DMAc
Acrylic fibre production: DMAc is a preferred solvent for organic wet spinning of acrylic fibres, where its solvency for polyacrylonitrile gives uniform dope and good fibre properties.
Polyimide and high-performance polymers: it is used as the casting and spinning solvent for polyimide films and fibres, including the polyimide precursor solutions used in electronics and insulation.
Extraction processes: DMAc extracts butadiene from ethylene-cracking C4 cuts and separates styrene from C8 fractions, and it is used in the purification of benzene and cyclohexene streams.
Coatings and cleaning: it acts as a solvent in specialty coatings and resin-dissolving formulations where slow evaporation and strong solvency are required.
Other uses: electrolyte solvent, reaction medium and catalyst, crystallisation solvent for organic intermediates, and a process solvent in pharmaceutical manufacturing.
Safety, Handling and Storage
DMAc is not a low-hazard solvent. Under the harmonised European classification it is a Category 1B reproductive toxicant, carrying the hazard statement that it may damage the unborn child, and it is also classified as harmful by inhalation and in contact with skin, as a skin and eye irritant and as a respiratory irritant. It is listed as a substance of very high concern because of its reproductive toxicity, so substitution and containment are the preferred control strategies wherever feasible.
Engineering controls should come first: closed systems, local exhaust ventilation at transfer and sampling points, and safe handling of the vapour generated at elevated temperature. Chemical-protective gloves resistant to amides, splash goggles, a face shield and appropriate coveralls are standard. Occupational exposure limits for DMAc normally carry a skin notation, which means dermal absorption contributes to body burden and gloves alone are not a complete barrier.
Store DMAc in sealed carbon steel or stainless steel containers in a cool, dry, well-ventilated area away from strong oxidisers, acids and bases. Many plastics, rubbers and paints are softened or dissolved by the solvent, so gaskets, hoses and pump seals must be selected for amide service.
Frequently Asked Questions
Q: Is dimethylacetamide soluble in water?
Yes. DMAc is completely miscible with water in all proportions at room temperature, and it is also miscible with alcohols, ethers, esters, chlorinated solvents and aromatic solvents.
Q: What is the boiling point of DMAc?
Approximately 164 to 166 °C at standard atmospheric pressure, which makes DMAc a high-boiling solvent that can be purified by distillation.
Q: Is DMAc stable during storage?
Yes, when kept sealed and dry. Stability falls in the presence of strong acids or bases, especially at high temperature, because hydrolysis of the amide group is then accelerated.
Q: What are the main industrial uses of DMAc?
Acrylic fibre spinning, polyimide film and fibre production, butadiene extraction, styrene recovery, specialty coatings and pharmaceutical process chemistry.
Q: What safety precautions are needed when handling DMAc?
Closed handling and local exhaust ventilation, suitable chemical-protective gloves and eye protection, and control of vapour at elevated temperature, because DMAc is a reproductive toxicant that can also be absorbed through the skin.





