What Is Benzaldehyde Oxime? Identity and Nomenclature
Benzaldehyde oxime, also written benzaldoxime, is the aromatic aldoxime obtained when benzaldehyde is treated with a hydroxylamine source. It is a colourless to off-white crystalline solid that occupies a very specific niche in fine chemistry: it is not a formulated product and carries no INCI designation for cosmetic use, but it is a widely traded synthesis intermediate and a classic reagent in analytical laboratories. Its molecular formula is C7H7NO, its molecular weight is 121.14 g/mol, and its CAS Registry Number is 932-90-1. Commercial documentation may list it as benzaldehyde oxime, benzaldoxime, (E)-benzaldehyde oxime, benzaldehyde, oxime, or phenylmethanal oxime; all of these names refer to the same substance and should cross-check to CAS 932-90-1 on the incoming certificate of analysis.
Structurally the molecule is compact: a phenyl ring joined to a single CH=N-OH group. That one oxime group explains almost every commercial use, because it can be reduced to a primary amine, dehydrated to a nitrile, hydrolysed back to the parent aldehyde, converted into nitrone or hydroximoyl chloride intermediates, or cyclised into nitrogen heterocycles. For a process chemist, benzaldehyde oxime is therefore best described as a selectively transformable, protected nitrogen handle attached to an aromatic scaffold. For a procurement team, it is a low-tonnage but specification-sensitive intermediate whose value depends far more on assay, isomer ratio and water content than on tonnage.
Physical and Chemical Properties
The technical material is a crystalline solid with a faint characteristic odour. It is only sparingly soluble in water and dissolves readily in alcohols, ketones, esters, chlorinated solvents and aromatic hydrocarbons. Because ordinary commercial batches are mixtures of two geometric isomers with different crystal habits and slightly different melting behaviour, appearance and melting range must be read together with the isomer ratio rather than in isolation. A batch that looks visually correct but shows a widened melting range is frequently telling the buyer something about isomer distribution or residual solvent, not about purity in the crude sense.
| Property | Typical value or description |
|---|---|
| CAS Registry Number | 932-90-1 |
| Molecular formula | C7H7NO |
| Molecular weight | 121.14 g/mol |
| Appearance | Colourless to off-white crystalline solid, flakes or powder |
| Melting range | Typically in the low thirties for mixed E/Z technical material (commonly quoted around 30-33 degrees C); the separated isomers melt higher and are specified individually by specialist suppliers |
| Boiling point | Around 118-120 degrees C at 10 mmHg; vacuum distillation is the normal purification route because atmospheric boiling causes decomposition |
| Relative density | Approximately 1.1 g/cm3 at 20 degrees C |
| Solubility | Sparingly soluble in water; freely soluble in ethanol, diethyl ether, chloroform, dichloromethane and toluene |
| Acid-base behaviour | Weakly acidic oxime proton; the nitrogen can be protonated under strongly acidic conditions, which is the basis of salt formation and of hydrolytic cleavage back to benzaldehyde |
| Stability and incompatibilities | Stable under ordinary ambient conditions when kept dry; keep away from strong oxidising agents, strong acids and bases, acid chlorides and anhydrides, and from prolonged exposure to light |
E/Z Isomerism and Why It Matters Commercially
All oximes exist as E and Z geometric isomers because rotation around the carbon-nitrogen double bond is restricted and the two substituents on the carbon and the hydroxyl group on the nitrogen adopt fixed relative positions. In benzaldehyde oxime the E form, in which the phenyl ring and the hydroxyl group lie on opposite sides of the C=N bond, is the thermodynamically preferred arrangement in equilibrated material. The Z form is achievable but tends to isomerise toward the E form under acidic catalysis and heat.
Isomerism is not an academic detail in this trade, for three practical reasons. First, melting range and crystallisation behaviour differ between the isomers, so the E/Z ratio controls whether a batch is a free-flowing flake or a waxy, sticky solid that is difficult to discharge from a drum. Second, downstream reactivity differs: reductions and dehydrations proceed at different rates and sometimes toward different products depending on geometry, and reactions that need a nitrile oxide intermediate are sensitive to which isomer is charged. Third, analytical quantification depends on it: a gas chromatography or HPLC method must either resolve the two peaks or state explicitly that the result is reported as the sum of isomers. Any specification that quotes an assay figure without stating whether it is isomer-resolved or isomer-summed is incomplete, and buyers should require that distinction in writing before a first order.
Grades, Specifications and Analytical Control
Benzaldehyde oxime is normally offered in three commercial bands. Industrial or technical grade is intended for further chemical conversion, with assay controlled by gas chromatography and with isomer ratio, water and appearance as the decisive parameters. Pharmaceutical intermediate grade is used where the oxime feeds a route to a registered active substance, so the specification adds identity confirmation by infrared and nuclear magnetic resonance spectroscopy, tighter chromatographic purity, residual solvent control consistent with ICH Q3C and elemental impurity control consistent with ICH Q3D, plus a defined heavy-metal limit. Reagent or analytical grade is supplied in small pack sizes for laboratory use and is usually differentiated by documentation, packaging and small-batch traceability rather than by a fundamentally different specification.
Whichever band a buyer purchases, the same control logic applies: identity, purity, water, residual solvents and physical form must all be verified against a written specification before release. The table below shows a workable verification framework that can be lifted directly into a purchase specification or an incoming inspection protocol.
| Control parameter | Typical requirement | Method basis |
|---|---|---|
| Identity | Conforms to reference | Infrared and proton NMR spectroscopy, plus retention time match |
| Assay | Typically 98.0% minimum for technical grade; 99.0% minimum for intermediate grade | Gas chromatography or HPLC against an external standard, with the isomer-resolution convention stated |
| Isomer ratio | E/Z distribution declared and reproducible batch to batch | Chromatographic peak normalisation |
| Water content | Low single-digit tenths of a percent for hydrolysis-sensitive downstream steps | Karl Fischer titration as described in GB/T 6283 |
| Appearance | Colourless to off-white, free of visible foreign matter | Visual examination against a standard |
| Melting range | Consistent with the declared isomer ratio | Capillary melting point determination |
| Residue on ignition | Low limit (for example 0.1% maximum) to control inorganic carry-over from neutralisation salts | Gravimetric ignition or sulphated ash |
| Heavy metals | Controlled where pharmaceutical use is intended | Elemental impurity testing per ICH Q3D expectations |
| Packaging integrity | Sealed, lined, moisture-tight | Visual and documentation check on receipt |
Production Routes and Supply-Chain Position
The established manufacturing logic for benzaldehyde oxime is a condensation: benzaldehyde (CAS 100-52-7, C7H6O) is brought together with a hydroxylamine source, most often in the form of a hydroxylamine salt, in an aqueous-alcoholic or aqueous-organic medium held within a buffered pH window by a mild base such as sodium acetate or by controlled addition of alkali. The oxime that forms is only sparingly water-soluble, so it is normally isolated by cooling and crystallisation, by filtration of the precipitated solid, or by extraction into a water-immiscible solvent followed by solvent recovery. Crude material is upgraded by recrystallisation or, where the melt behaviour permits, by vacuum distillation, and the finished solid is dried, milled to a defined particle-size profile if required, and packed under moisture-tight conditions. Route selection is driven by isomer ratio control, by the salt load that has to be washed out, and by effluent considerations rather than by any exotic chemistry; the practical know-how lies in pH and phase control and in drying, not in the reaction itself.
Upstream, the two raw materials that dominate cost are benzaldehyde and the hydroxylamine source, both of which are bulk commodities with their own cyclical price behaviour. Downstream, benzaldehyde oxime feeds several well-defined product families. Dehydration gives benzonitrile (CAS 100-47-0), a solvent and intermediate in its own right. Reduction gives benzylamine (CAS 100-46-9) and, under different conditions, other reduced amines. Hydrolysis returns benzaldehyde, a permitted flavouring substance widely used in the food and fragrance industries. Conversion into hydroximoyl halides opens access to nitrile oxides, the classic partners in cycloaddition to give isoxazole and isoxazoline rings, which is why the oxime sits high on the intermediate list for certain crop-protection and pharmaceutical scaffolds. O-substituted oxime ethers formed from it are also valuable as protected intermediates in medicinal chemistry. The oxime therefore sits at a genuine junction in the fine-chemical supply chain, small in volume but difficult to substitute without redesigning the downstream route.
Applications Across Industries
Agrochemical intermediates. The most robust commercial pull for benzaldehyde oxime is in crop-protection chemistry, where oxime-derived nitrile oxides and oxime ethers are used to build heterocyclic actives. Buyers in this segment should expect to specify the isomer ratio tightly, because a shift in the E/Z balance can change the yield and the impurity profile of the ring-closure step.
Pharmaceutical and medicinal chemistry. In medicinal chemistry and in intermediate manufacture, the oxime is used as a masked amine and as a component of oxime ether or oxime ester linkages that are deliberately designed to be hydrolytically labile. Documentation quality, not just chemical purity, is the differentiator here: batch traceability, residual solvent statements and elemental impurity data are part of the product.
Analytical and laboratory chemistry. Oximes are classical derivatisation reagents. Benzaldehyde oxime is used in identification and derivatisation work, as a ligand in coordination and complexation studies, and as a standard for method development where an aromatic oxime is needed as a model compound. It also appears in corrosion-inhibition research, since aromatic oximes adsorb onto metal surfaces through the nitrogen lone pair and the hydroxyl group.
Materials and organic electronics research. Oxime-based ligands and oxime-functionalised ligands are studied as building blocks for emissive metal complexes and for other functional materials. This is a research-stage demand, but it is a real one and it explains the appearance of the compound in catalogues alongside more conventional intermediates.
Flavour and fragrance adjacency. Benzaldehyde oxime itself is not registered as a flavouring substance, but it is a convenient, storage-stable latent form of benzaldehyde, which is permitted as a flavouring substance in many jurisdictions and is one of the most widely used almond-type odourants. Suppliers close to the flavour industry should keep this distinction clear in technical literature: the oxime is the precursor, not the approved aroma material.
What it is not. Benzaldehyde oxime is not a general-purpose solvent, not a cosmetic ingredient and not a stabiliser that can be dropped into a formulation. Any request to use it as a direct additive should be treated as a technical enquiry requiring a full safety and regulatory review rather than as a catalogue order.
Safety, Handling, Storage, Transport and Compliance
Benzaldehyde oxime should be handled as an irritant fine chemical. Commercial safety data sheets for the material, prepared in the ISO 11014 format, generally carry hazard communication for skin and eye irritation and for harmful effects if swallowed, which corresponds to standard laboratory practice: nitrile gloves, safety glasses or goggles, a lab coat or coveralls, and local exhaust ventilation wherever dust can be generated. Wet or dusty operations should be engineered to control dust at source, and good housekeeping with immediate clean-up of spills is essential because a dry crystalline solid can be swept into the air. Eye-wash facilities and washing facilities should be available where the material is handled in quantity.
For storage, the priority parameters are moisture, heat and light. A cool, dry, well-ventilated area away from direct sunlight and away from strong oxidising agents, strong acids and alkalis, and acid chlorides or anhydrides is appropriate. Containers should be kept closed when not in use, and part-used drums should be resealed promptly; because the material is hygroscopic enough for water content to matter in downstream reactions, opened packaging should not be left standing in humid conditions. Shelf life under good storage is normally stated in terms of years, with the residual water and isomer ratio being the parameters most likely to drift.
Packaging for export normally uses polyethylene-lined fibre drums or lined multiwall bags in 25 kg net units, with larger lined drums available for industrial volumes. Transport markings should follow GB/T 191 for pictorial handling symbols, and the governing safety data sheet should be attached to every shipment. Under conventional classification the solid is not normally regulated as dangerous goods for road, sea or air transport, but classification must always be confirmed against the supplier's current safety data sheet and the applicable ADR, IMDG or IATA requirements before a shipment is booked. Correct shipping names, hazard classes and packing groups, if any apply, must appear on the transport documents exactly as classified.
On the regulatory side, buyers should ask three questions. Is the substance registered or otherwise compliant for import into the destination market, including the applicability of REACH registration obligations for the European Economic Area and inventory listing status for the United States. Is it intended for a regulated application, since pharmaceutical use brings ICH Q3C residual solvent and ICH Q3D elemental impurity expectations into the specification and food or cosmetic use would require an entirely different authorisation route that this substance does not normally hold. And is the documentation complete, meaning a certificate of analysis that matches the specification clause by clause, a safety data sheet in the required language, and, where relevant, a statement on residual solvents and heavy metals. Documentation gaps are the most common reason a technically acceptable batch is rejected at goods-in.
FAQ
Q: What is the CAS number and molecular formula of benzaldehyde oxime?
Benzaldehyde oxime is CAS 932-90-1, with molecular formula C7H7NO and a molecular weight of 121.14 g/mol. It is also traded as benzaldoxime and phenylmethanal oxime; any supplier document quoting a different CAS number for the same name should be queried before ordering.
Q: What assay and purity should a buyer expect for technical grade material?
Technical grade is normally specified at 98.0% minimum by gas chromatography or HPLC, with water controlled by Karl Fischer titration and with the E/Z isomer ratio declared. Intermediate grade used in pharmaceutical routes is usually specified at 99.0% minimum and adds identity testing by infrared and NMR spectroscopy.
Q: Why does the E/Z isomer ratio matter in a purchase specification?
The two geometric isomers differ in melting range, crystallisation behaviour and reactivity, so the ratio affects both the physical form of the delivered solid and the performance of the downstream reaction. A specification that quotes assay without stating whether the value is isomer-resolved or the sum of isomers is ambiguous and should be clarified in writing.
Q: How should benzaldehyde oxime be stored and how long does it keep?
Store it cool, dry and out of direct sunlight, away from strong oxidising agents, strong acids and bases, and acid chlorides or anhydrides. Keep containers closed, because moisture pick-up raises water content and can affect hydrolysis-sensitive downstream steps. Under these conditions the material is stable for years, with water content and isomer ratio as the parameters most likely to change.
Q: Is benzaldehyde oxime classified as dangerous goods for transport?
It is generally supplied without a dangerous goods classification for road, sea or air transport, and it is handled as an irritant fine chemical in the workplace. Because classification practice and national rules can differ, the governing safety data sheet issued with the shipment must be checked and the applicable ADR, IMDG or IATA requirements confirmed before booking transport.
Q: What is the main industrial use of benzaldehyde oxime?
Its largest technical role is as an intermediate: dehydrated it gives benzonitrile, reduced it gives benzylamine, hydrolysed it returns benzaldehyde, and converted into a hydroximoyl halide it becomes a nitrile oxide precursor for building isoxazole and isoxazoline rings. It is also used as a laboratory derivatisation and complexation reagent and in corrosion-inhibition research.





