How Heat Resistance Is Classified in Thermoplastics
Thermoplastics are conventionally grouped into three tiers by long-term service temperature. General-purpose plastics, including polyethylene, polypropylene, polystyrene, polyvinyl chloride and ABS, are used below about 100 degrees Celsius and account for the largest volumes in packaging, household goods and toys. Engineering plastics work in the range of roughly 100 to 150 degrees Celsius; the five established families are polyamide, polyoxymethylene, polybutylene terephthalate, polycarbonate and modified polyphenylene ether. High-temperature engineering plastics are defined by continuous service above 150 degrees Celsius, and they combine that rating with flame retardancy, dimensional stability, electrical performance and, in a growing number of applications, the replacement of metal parts in electronics, aerospace, medical equipment, automotive and defence hardware.
The definition is worth stating carefully, because the phrase high temperature is used loosely in marketing material. Three different numbers have to be kept apart: the glass transition temperature of an amorphous polymer, the crystalline melting temperature of a semi-crystalline polymer, and the heat deflection temperature measured under a defined load. The first two are material constants determined by thermal analysis, while heat deflection temperature per ISO 75 or ASTM D648 depends on the test load, usually 0.45 MPa or 1.82 MPa, and is therefore only comparable between materials when the same load and specimen geometry are quoted.
None of those three numbers equals the practical continuous use temperature. For long-term service the recognised engineering reference is the relative thermal index derived from long-term ageing tests, described in UL 746B for electrical insulation systems. A designer who specifies a resin from a melting point alone will misjudge amorphous and semi-crystalline materials in opposite directions. Semi-crystalline polymers such as polyphenylene sulfide and polyetheretherketone retain load-bearing capability close to their melting range because the crystalline phase reinforces the structure, whereas amorphous polymers such as polysulfone soften soon after passing their glass transition. That single distinction explains most unexpected failures in high-temperature assemblies.
The Eight Families at a Glance
The comparison below summarises the eight families discussed in this article. Continuous use temperatures and transition temperatures are indicative figures for unfilled or lightly filled grades; mineral, glass fibre and carbon fibre reinforcement shifts heat deflection temperature, stiffness and cost upward, and the grade datasheet always takes precedence over a general table.
| Family | Representative polymers | Indicative continuous use | Transition temperature | Notable strengths |
|---|---|---|---|---|
| High-temperature polyamides | PA46, PPA, PARA | 150 to 170 degrees Celsius | PA46 melts near 295 degrees Celsius | Toughness, wear resistance, good chemical resistance |
| Polyphenylene sulfide | PPS, CAS 25212-74-2 | 200 to 220 degrees Celsius reinforced | Melts near 280 to 285 degrees Celsius; glass transition near 90 degrees Celsius | Inherent flame retardancy, very low moisture uptake, broad chemical resistance |
| Polyaryletherketones | PEEK, CAS 31694-16-3; PEKK; PEK; PEKEKK | Around 250 degrees Celsius | PEEK melts near 343 degrees Celsius; glass transition near 143 degrees Celsius | Best balanced mechanical performance, hydrolysis and chemical resistance |
| Polyetherimide | PEI | Around 170 degrees Celsius | Glass transition near 217 degrees Celsius | Amorphous, high strength and modulus, low smoke, good dielectric strength |
| Polyimide | PI, thermoset and thermoplastic | 250 to 300 degrees Celsius and above for selected grades | No melting point for thermoset grades | Extreme heat resistance, very low outgassing, radiation resistance |
| Liquid crystal polymers | LCP aromatic copolyesters | 200 to 240 degrees Celsius | Melts between about 280 and 350 degrees Celsius depending on the grade | Thin-wall flow, very low warpage and thermal expansion |
| Polysulfone | PSU | 150 to 160 degrees Celsius | Glass transition near 185 degrees Celsius | Transparency, hydrolytic stability, repeated steam sterilisation |
| Polyethersulfone and polyphenylsulfone | PESU, PPSU | 180 to 190 degrees Celsius | Glass transition near 220 degrees Celsius | High glass transition, hot water resistance, toughness |
High-Temperature Polyamides: PA46, PPA and PARA
Polyamides are the workhorses of high-temperature engineering because they combine a low price with good toughness. Three structural classes are used at the top end of the temperature range.
Aliphatic high-temperature nylon is represented by PA46, built from tetramethylenediamine and adipic acid. The shorter repeat unit produces a higher amide density than PA66, which raises the melting point to approximately 295 degrees Celsius, increases crystallinity and speeds crystallisation in the mould. The result is a high heat deflection temperature, excellent fatigue and wear behaviour, and good performance in gears, chain tensioners, bearings and electrical components close to engines. The trade-off is a higher equilibrium moisture absorption than semi-aromatic polyamides, so dimensions and stiffness must be evaluated in the conditioned state rather than in the dry state.
Semi-aromatic polyamides, usually abbreviated PPA, are based on aromatic diacids such as terephthalic acid combined with aliphatic diamines. Introducing the aromatic ring raises the melting range, which can exceed 300 degrees Celsius in the highest terephthalic grades, and sharply lowers moisture uptake compared with PA66. That combination is the reason PPA dominates surface-mount connectors, where parts must survive lead-free reflow soldering without blistering or dimensional change, and also appears in under-hood housings, motor end caps and pump components.
Fully aromatic polyamides, known as PARA, replace both the diacid and the diamine with aromatic units. The rigid backbone delivers very high strength and stiffness, high heat deflection temperature and outstanding dimensional stability under load, which suits precision parts exposed to sustained high temperature, such as connector bodies, bearing cages and structural components in electrical equipment. The cost per kilogram is the highest of the three classes, and processing requires higher melt temperatures, so PARA is selected where dimensional precision at temperature is the deciding requirement rather than where cost dominates.
Polyphenylene Sulfide (PPS)
Polyphenylene sulfide, CAS 25212-74-2, is one of the most widely used special engineering plastics, and the growth rate reflects its unusual combination of properties. The polymer is semi-crystalline, melts near 280 to 285 degrees Celsius, and has a glass transition around 90 degrees Celsius, yet reinforced grades are routinely qualified for continuous service in the 200 to 220 degrees Celsius range. The aromatic sulfide repeat unit gives inherent flame retardancy, with the unfilled polymer achieving the highest flammability classification without added flame retardants, and a limiting oxygen index in the region of 40% or more.
The practical profile of the resin is defined as much by its weaknesses as its strengths. Unfilled PPS is brittle and rarely used alone, so commercial grades are almost always compounded with glass fibre, mineral filler, or a combination of the two, which raises stiffness and heat deflection temperature while lowering moulding shrinkage. Moisture absorption is very low, so parts hold their dimensions through humidity cycling and maintain stable electrical properties. Chemical resistance is broad, extending to fuels, oils, coolants, acids, bases and most solvents across the temperature range of the material, which explains its use in automotive cooling and fuel handling systems, electrical connectors, coil formers, LED housings, pump bodies and chemical process equipment. Dimensional stability and resistance to creep at temperature make it a common replacement for die-cast metal in fluid handling hardware, provided that impact loading is assessed against the reinforced grade rather than the base polymer.
The Polyaryletherketone (PAEK) Family
Polyaryletherketones share a main chain of phenylene rings connected by ether and ketone linkages. The ratio and sequence of the two linkages define the family members: polyetheretherketone, polyetherketoneketone, polyetherketone and the higher members of the series. Increasing the proportion of ketone groups stiffens the backbone and raises the glass transition and melting temperatures, so the family offers a ladder of performance within one chemistry.
Polyetheretherketone, CAS 31694-16-3, is the most widely used member. It melts near 343 degrees Celsius, has a glass transition near 143 degrees Celsius, and is qualified by many compounders for continuous service around 250 degrees Celsius. Density is about 1.30 g/cm3, and unfilled tensile strength is in the region of 100 MPa, with glass fibre and carbon fibre grades substantially higher and much stiffer. The polymer resists hydrolysis, so it survives repeated steam and hot water exposure, and it resists most oils, fuels and solvents. These properties, together with a well-established medical grade sector where biocompatibility has been assessed, place PEEK in aerospace brackets and bushings, semiconductor wafer handling equipment where low particle generation and plasma resistance are required, oil and gas seals and back-up rings, and machined medical components. Its price is correspondingly high, so designs normally minimise material volume and use reinforcing fillers rather than solid sections.
Polyetherketoneketone uses ether-ketone-ketone units instead of the ether-ether-ketone sequence. The change lowers the crystallisation rate and alters the processing window, gives higher glass transition and modulus in some grades, and improves compression behaviour, which is valued in aerospace composite matrices and in additive manufacturing where slower crystallisation helps interlayer bonding. Polyetherketone carries an even higher ketone ratio and therefore a higher glass transition, while the extended members of the series are niche products used where a specific combination of stiffness and thermal resistance is required. Because all members are semi-crystalline and chemically related, the selection question is usually one of processing window and cost rather than of fundamental compatibility with the service environment.
Polyetherimide (PEI) and Polyimide (PI)
Polyetherimide is an amorphous polymer with a glass transition near 217 degrees Celsius and an indicative continuous use temperature around 170 degrees Celsius. It offers high strength and modulus, natural flame resistance with low smoke emission, stable dielectric properties and transparency in an amber tone. It is not resistant to strong bases or to some chlorinated solvents, and it is notch sensitive, so designs avoid sharp internal corners. Typical uses are electrical and electronic components, connector housings, semiconductor handling fixtures, medical trays that must withstand repeated sterilisation, and aircraft interior parts where low smoke and toxicity matter.
Polyimide is an aromatic heterocyclic polymer containing imide linkages. Thermoset polyimides formed from a dianhydride and a diamine do not melt and show no measurable glass transition in the useful range, which allows selected grades to serve continuously above 300 degrees Celsius. They combine excellent electrical insulation, radiation resistance and mechanical strength with extremely low outgassing in vacuum, a property that is decisive in space hardware, where volatile condensable material can fog optical surfaces. Polyimide film is used as flexible circuit substrate, wire insulation, thermal blanket material and slot liner. Thermoplastic polyimides are melt processable and easier to injection mould, but their temperature ceiling is lower than that of the thermoset types. Both are high-cost materials, usually machined or compression moulded rather than injection moulded in volume, and some grades are sensitive to hydrolytic attack at high temperature, so hot wet service must be validated rather than assumed.
Liquid Crystal Polymers (LCP)
Liquid crystal polymers are aromatic copolyesters whose rigid rod-like chains align in the melt, which is the source of their distinctive behaviour. The ordered melt has a very low viscosity, so thin sections fill easily at moderate pressure and cycle times are short. The aligned structure produces high strength and stiffness in the flow direction, very low thermal expansion, minimal warpage and excellent dimensional precision, and the low dielectric loss at high frequency suits radio frequency and antenna components in mobile devices. Melting points vary widely with monomer composition, spanning roughly 280 to 350 degrees Celsius by grade, and filled grades deliver heat deflection temperatures above 240 degrees Celsius.
The anisotropy of the aligned structure is the main design constraint. Properties measured along the flow direction differ from those measured across it, weld lines are weak, and thick sections can show internal voids because the melt solidifies with a skin-core structure. Mould design therefore places gates to position flow direction along the load path, avoids weld lines in structural areas, and keeps wall sections thin and uniform. LCP is used for surface-mount connectors, sockets, camera module components, switches, and precision housings, and its low water absorption keeps electrical performance stable through assembly and service.
Polysulfones: PSU, PESU and PPSU
The polysulfone family consists of amorphous thermoplastics built on bisphenol chemistry with sulfone linkages in the backbone. Polysulfone itself has a glass transition near 185 degrees Celsius and an indicative continuous use temperature of 150 to 160 degrees Celsius. Polyethersulfone and polyphenylsulfone raise the glass transition to about 220 degrees Celsius, with continuous use ratings in the 180 to 190 degrees Celsius range, and polyphenylsulfone adds better toughness and hydrolytic stability. The three materials share transparency, good dimensional stability, resistance to mineral acids and bases, and outstanding tolerance of repeated steam sterilisation, which is why they appear in sterilisation trays, surgical instrument handles, dialysis hardware, humidifier components, milk processing equipment, water treatment manifolds, membrane housings and demanding electrical parts.
Their weakness is stress cracking in contact with ketones and chlorinated solvents, and amorphous polymers in general are more sensitive to stress cracking than semi-crystalline ones. Moulded-in stress must therefore be minimised through proper drying, uniform wall sections and generous radii, and the finished part should be evaluated in the cleaning agents and disinfectants it will actually meet, since repeated exposure to aggressive disinfectant chemistry is a common cause of field failure in medical hardware.
Selection Rules That Hold Up in Service
Material selection for high-temperature applications follows a sequence, and skipping a step is what produces expensive redesigns. The practical order is the following.
Define the temperature profile, not a single temperature. Record continuous temperature, peak excursions, their duration and their frequency. A part that sees brief peaks near 250 degrees Celsius annually has a different requirement from one held at 200 degrees Celsius for thousands of hours.
Use the right thermal metric. Short-term stiffness at temperature is judged from heat deflection temperature at a stated load under ISO 75 or ASTM D648; long-term capability is judged from the relative thermal index of UL 746B; creep resistance under sustained load is judged from isothermal creep curves, which no single data sheet number can replace.
Match mechanical demand to reinforcement. Unfilled polymers rarely enter structural high-temperature service, because glass fibre, carbon fibre or mineral fillers raise stiffness, creep resistance and heat deflection temperature simultaneously, at the cost of impact strength and anisotropic shrinkage.
Screen the chemical environment. Fuels, coolants, hydraulic fluids, cleaning agents and disinfectants all matter, and the combination of chemical exposure with temperature is more aggressive than either alone. Special attention belongs to hydrolysis, where polyamides and some polyimide grades are affected while polyaryletherketones and polyphenylene sulfide are not.
Check electrical and dimensional requirements. Compare dielectric strength, comparative tracking index per IEC 60112, volume resistivity and thermal expansion against the design limits, and remember that moisture uptake in polyamides changes both dimensions and dielectric behaviour.
Confirm the processing route. Injection moulding, extrusion, machining and additive manufacturing each favour different families. Liquid crystal polymers and polysulfones demand specific drying and melt profiles, polyimides are usually machined or compression moulded, and some high-temperature grades need heated tooling to control crystallisation.
Validate with a prototype under real conditions. Short-term data sheets cannot predict creep rupture, thermal cycling fatigue or the interaction of chemical exposure with stress. A load-bearing prototype test at temperature is cheaper than a field failure.
Applied to the eight families, the ranking is fairly stable. Polyphenylene sulfide offers the best balance of cost, heat resistance and chemical resistance for automotive and electrical parts up to the 200 to 220 degrees Celsius band. Polyetheretherketone takes over when maximum mechanical performance, hydrolysis resistance and wear behaviour are required, or when the environment is too aggressive for other polymers. Polyimide is reserved for the most extreme temperatures and for vacuum service where outgassing is critical. Liquid crystal polymers are chosen for thin-wall precision electronics and high-frequency parts, polyetherimide for transparent, flame resistant electrical and medical items, and the polysulfones for parts that must be repeatedly steam sterilised or must remain transparent in hot water service.
Drying and Processing Notes
Most of these polymers absorb moisture, and all of them are processed well above the boiling point of water, so inadequate drying produces hydrolysis, splaying, bubbles and loss of mechanical properties. The drying schedules below are typical starting points reported for each family; the resin grade datasheet governs, and thicker mouldings, humid climates and recycled content generally require longer or hotter drying.
| Family | Typical drying schedule | Typical melt processing range | Processing caution |
|---|---|---|---|
| PA46 | Around 100 degrees Celsius for 4 hours or longer | Roughly 290 to 320 degrees Celsius | Moisture sensitive; condition parts before measuring dimensions |
| PPA and PARA | Around 120 to 150 degrees Celsius | Above 300 degrees Celsius for high terephthalic grades | High melt temperatures demand hot runners rated for the duty |
| PPS | Around 150 to 160 degrees Celsius for 3 hours | Roughly 300 to 340 degrees Celsius | Reinforced grades are abrasive; use wear-resistant barrels |
| PEEK | Around 150 degrees Celsius for 3 hours | Roughly 350 to 400 degrees Celsius | Heated tooling near 180 degrees Celsius for crystallinity |
| PEI | Around 150 degrees Celsius for 4 hours | Roughly 340 to 400 degrees Celsius | Notch sensitive; avoid sharp corners in design |
| LCP | Around 150 degrees Celsius for 3 hours | Grade dependent, typically 280 to 350 degrees Celsius | Anisotropic flow; control gate position and weld lines |
| PSU, PESU, PPSU | Around 150 to 180 degrees Celsius for 3 to 4 hours | Roughly 330 to 390 degrees Celsius | Minimise moulded-in stress to avoid stress cracking |
| PI | Pre-dried by the compounder; parts often machined | Not melt processed in thermoset grades | Compression moulding or sintering plus machining |
Two further processing points recur across the families. First, regrind must be limited and controlled, because high-temperature polymers degrade on repeated thermal history and the resulting loss of molecular weight is invisible in the moulded part until it fails in service. Second, tool and barrel temperatures are part of the specification for semi-crystalline materials: cooling a polyaryletherketone or polyphenylene sulfide part too quickly leaves a thin, brittle skin over an incompletely crystallised core, so tool temperature should follow the grade recommendation rather than be set for the shortest cycle time.
FAQ
Q: What is the definition of a high-temperature engineering plastic?
It is a thermoplastic qualified for long-term continuous service above 150 degrees Celsius, usually combined with flame retardancy, dimensional stability, electrical performance and mechanical strength. General-purpose plastics work below about 100 degrees Celsius and the five established engineering families work between roughly 100 and 150 degrees Celsius.
Q: Is polyphenylene sulfide suitable for continuous service at 200 degrees Celsius?
Yes, reinforced grades of polyphenylene sulfide, CAS 25212-74-2, are commonly qualified for continuous service in the 200 to 220 degrees Celsius band, provided that impact loading is evaluated against the reinforced grade. The base polymer is brittle and is almost always compounded with glass or mineral filler before use in structural parts.
Q: What is the difference between PEEK and PEKK?
Both belong to the polyaryletherketone family. Polyetheretherketone contains ether-ether-ketone repeating units and melts near 343 degrees Celsius, while polyetherketoneketone uses ether-ketone-ketone units, which lowers the crystallisation rate and changes the processing window while raising the glass transition in some grades. PEEK is the more widely used of the two.
Q: Why is polyimide used in aerospace and vacuum equipment?
Polyimide withstands continuous temperatures above 300 degrees Celsius in selected grades and combines this with excellent electrical insulation, radiation resistance and very low outgassing. The low outgassing is decisive in vacuum and space hardware, where condensed volatiles would contaminate optics and thermal control surfaces.
Q: Can high-temperature plastics replace metal components?
In many cases they can, and polyphenylene sulfide, polyetheretherketone and liquid crystal polymers are established replacements for die-cast aluminium and machined steel in fluid handling, connectors and precision hardware. The substitution reduces weight and eliminates corrosion, but load bearing at temperature, creep and impact limits must be verified on the reinforced grade before a metal part is redesigned in polymer.
Q: How should these polymers be dried before moulding?
Most are hygroscopic and must be dried before processing, typically in the range of 100 to 180 degrees Celsius for three to four hours depending on the family, as stated on the resin grade datasheet. Processing wet resin causes hydrolysis, silver streaking and loss of mechanical properties, and the damage cannot be reversed by later drying.
Q: Which standards are used to compare these materials fairly?
Thermal performance is compared using heat deflection temperature per ISO 75 or ASTM D648 at a stated load, long-term capability per UL 746B, and softening behaviour per ISO 306. Mechanical data follow ISO 527 for tensile properties and ISO 178 or ISO 179 for flexural and impact behaviour, melt flow is measured by ISO 1133 or ASTM D1238, density by ASTM D792, water absorption by ASTM D570 and flammability by UL 94, with Chinese equivalents such as GB/T 1040, GB/T 1634 and GB/T 3682 used in domestic procurement.





